数据搜索系统,热门电子元器件搜索 |
|
TMP86PM29A 数据表(PDF) 1 Page - Toshiba Semiconductor |
|
TMP86PM29A 数据表(HTML) 1 Page - Toshiba Semiconductor |
1 / 8 page TMP86FM29 2004-03-01 Difference Comparison table of TMP86C829B/H29B/M29B/PM29A/PM29B/C929AXB and TMP86FM29 TMP86C829B TMP86CH29B TMP86CM29B TMP86PM29A TMP86PM29B TMP86C929AXB (Emulation chip) (Note 3) TMP86FM29F ROM 8 K (Mask ROM) 16 K (Mask ROM) 32 K (Mask ROM) 32 K (OTP) − 32 K (Flash) RAM 512 1.5 K 1.5 K 1.5 K − 2 K I/O 42 pin 42 pin (MCU part) 42 pin External Interrupt 5 pin 5 pin AD Converter 10-bit AD converter × 8 ch 10-bit AD converter × 8 ch Timer Counter 18-bit timer × 1 ch 8-bit timer × 4 ch 18-bit timer × 1 ch 8-bit timer × 4 ch Serial Interface 8-bit UART / SIO × 1 ch 8-bit UART / SIO × 1 ch LCD 32 seg × 4 com 32 seg × 4 com (Note 2) Key-on Wakeup 4 ch 4 ch Operating Voltage in MCU Mode 1.8 to 5.5 V at 4.2 MHz 2.7 to 5.5 V at 8 MHz 4.5 to 5.5 V at 16 MHz 1.8 to 5.25 V at 4.2 MHz 2.7 to 5.25 V at 8 MHz 4.5 to 5.25 V at 16 MHz 1.8 to 3.6 V at 4.2 MHz (External clock) 1.8 to 3.6 V at 8 MHz (Resonator) 2.7 to 3.6 V at 16 MHz Operating Temperature in MCU Mode −40 to 85℃ 0 to 60°C −40 to 85°C Writing to Flash Memory − 2.7 to 3.6V at 16 MHz 25°C ± 5°C CPU Wait (Note 1) N/A Available Note 1: The CPU wait is a CPU halt function for stabilizing of power supply of Flash memory. The CPU wait period is as follows. In the CPU wait period except RESET, CPU is halted but peripheral functions are not halted. Therefore, if the interrupt occurs during the CPU wait period, the interrupt latch is set. In this case, if the IMF has been set to “1”, the interrupt service routine is executed after CPU wait period. For details refer to 2.14 “Flash Memory” in TMP86FM29 data sheet. Thus, even if the same software is executed in 86FM29 and 86C829B/H29B/M29B/PM29A/PM29B /C929AXB, the operation process is not the same. Therefore, when the final operating confirmation on target application is executed for software development of Mask ROM Product (86C829B/H29B/M29B), not the Flash product (86FM29) but the OTP product (86PM29A/PM29B) should be used. Halt/Operate Condition Wait Time CPU Peripherals After reset release 2 10 /fc[s] Halt Halt Changing from STOP mode to NORMAL mode (at EEPCR<MNPWDW> = “1”) 2 10 /fc[s] Halt Operate Changing from STOP mode to SLOW mode (at EEPCR<MNPWDW> = “1”) 2 3 /fs[s] Halt Operate Changing from IDLE0/1/2 mode to NORMAL mode (at EEPCR<ATPWDW> = “0”) 2 10 /fc[s] Halt Operate Changing from SLEEP0/1/2 mode to SLOW mode (at EEPCR<ATPWDW> = “0”) 2 3 /fs[s] Halt Operate |
类似零件编号 - TMP86PM29A |
|
类似说明 - TMP86PM29A |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |