数据搜索系统,热门电子元器件搜索
  Chinese▼

Delete All
ON OFF
ALLDATASHEETCN.COM

X  

预览 PDF Download HTML

MC1GU064HCYB-0QC00 Datasheet(数据表) 38 Page - Samsung semiconductor

部件型号  MC1GU064HCYB-0QC00
说明  MultiMediaCard Specification
下载  66 Pages
Scroll/Zoom Zoom In 100% Zoom Out
制造商  SAMSUNG [Samsung semiconductor]
网页  http://www.samsung.com/Products/Semiconductor
标志 

MC1GU064HCYB-0QC00 Datasheet(HTML) 38 Page - Samsung semiconductor

Zoom Inzoom in Zoom Outzoom out
 38 page
background image
MultiMediaCard
TM
38
ERASE_GROUP_END(CMD36) command and finally it starts the erase process by issuing the
ERASE(CMD38) command. The address field in the erase commands is an Erase Group address in
byte units. The card will all LSB’s below the Erase Group size, effectively rounding the address down to
the Erase Group boundary.
If an erase command is received out of sequence, the card shall set the ERASE_SEQ_ERROR bit in
the status register and reset the whole sequence.
If an out of sequence(neither of the erase commands, except SEND_STATUS) command received, the
card shall set the ERASE_RESET status bit in the status register, reset the erase sequence and
execute the last command.
If the erase range includes write protected blocks, the shall be left intact and only the non-protected
blocks shall be erased. The WP_ERASE_SKIP status bit in the status register shall be set.
As described above for block write, the card will indicate that an erase is in progress by holding DAT
low The actual erase time may be quite long, and the host may issue CMD7 to deselect the card.
4.9.4 Write Protect Management
Card data may be protected against either erase or write. The entire card may be permanently write
protected by the manufacturer or content provider by setting the permanent or temporary write protect
bits in the CSD. Portions of the data may be protected (in units of WP_GRP_SIZE sectors as specified
in the CSD), and the write protection may be changed by the application. The SET_WRITE_PROT
command sets the write protection of the addressed write-protect group, and the CLR_WRITE_PROT
command clears the write protection of the addressed write-protect group. The SEND_WRITE_PROT
command is similar to a single block read command. The card shall send a data block containing 32
write protection bits (representing 32 write protect groups starting at the specified address) followed by
16 CRC bits. The address field in the write protect commands is a group address in byte units. The
card will ignore all LSB’s below the group size.
4.9.5 Card Lock/Unlock Operation
The password protection feature enables the host to lock a card while providing a password, which
later will be used for unlocking the card. The password and its size are kept in a 128-bit PWD and 8-bit
PWD_LEN registers, respectively. These registers are non-volatile so that a power cycle will not erase
them. Locked cards respond to (and execute) all commands in the "basic" command class (class 0)
and “lock card” command class. Thus the host is allowed to reset, initialize, select, query for status,
etc., but not to access data on the card. If the password was previously set (the value of PWD_LEN is
not‘0’) will be locked automatically after power on. Similar to the existing CSD and CID register write
commands the lock/unlock command is available in "transfer state" only. This means that it does not
include an address argument and the card has to be selected before using it. The card lock/unlock
command has the structure and bus transaction type of a regular single block write command. The
transferred data block includes all the required information of the command (password setting mode,
PWD itself, card lock/unlock etc.). The following table describes the structure of the command data
block.
Table 4-9 Card Lock Data Structure
Byte#
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
0
Reserved
ERASE
LOCK_
UNLOCK
CLR_
PWD
SET_
PWD
1
PWD_LEN
2
PWD_LEN+1
Password data




HTML 页

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42  43  44  45  46  47  48  49  50  51  52  53  54  55  56  57  58  59  60  61  62  63  64  65  66 


数据表 下载



相关电子零件

部件型号部件说明Html View制造商
MC56U032DCCADual Voltage MultiMediaCard Specification 1 2 3 4 5 MoreSamsung semiconductor
DMF5010NB-FWLCD Module Specification 1 2 3 4 5 MoreOPTREX CORPORATION
GL5ZJ44DEVICE SPECIFICATION FOR Light Emitting Diode 1 2 3 4 5 MoreSharp Electrionic Components
LQ084V2DS01DEVICE SPECIFICATION FOR TFT-LCD Module 1 2 3 4 5 MoreSharp Electrionic Components
PC357NTDEVICE SPECIFICATION FOR PHOTOCOUPLER 1 2 3 4 5 MoreSharp Electrionic Components
1MBI150SH-140Tentative target specification 1 2 Fuji Electric
K4S643232H64Mb H-die x32 SDRAM Specification 1 2 3 4 5 MoreSamsung semiconductor
PH967C6SPECIFICATION 1 2 3 4 5 MoreFuji Electric
DMC16207N-BLCD Module Specification 1 2 3 4 5 MoreOPTREX CORPORATION
K4H1G0438M1Gb M-die DDR SDRAM Specification 1 2 3 4 5 MoreSamsung semiconductor

链接网址


Privacy Policy
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ]  

关于 Alldatasheet    |   广告服务   |   联系我们   |   隐私政策   |   书签   |   链接交换   |   制造商名单
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl