数据搜索系统,热门电子元器件搜索
  Chinese▼

Delete All
ON OFF


BQ27743 Datasheet(数据表) 35 Page - Texas Instruments

部件型号  BQ27743
说明  Single-Cell Li-Ion Battery Fuel Gauge with Programmable Hardware Protection
下载  42 Pages
Scroll/Zoom Zoom In 100% Zoom Out
制造商  TI1 [Texas Instruments]
网页  http://www.ti.com
标志 

 35 page
background image
500ms / div
2V / div
2V / div
5V / div
5V / div
2V / div
2V / div
5V / div
5V / div
50ms / div
35
bq27743
www.ti.com
SLUSCM0A – JUNE 2017 – REVISED SEPTEMBER 2018
Product Folder Links: bq27743
Submit Documentation Feedback
Copyright © 2017–2018, Texas Instruments Incorporated
9.2.3.11 NFET Selection
The choice in NFETs for a single-cell battery pack design will depend on a variety of factors including package
type, size, and device cost as well as performance metrics such as drain-to-source resistance (rDS(on)), gate
capacitance, maximum current and power handling, and similar. At a bare minimum, it is recommended that the
selected FETs have a drain-to-source voltage (VDS) and gate-to-source (VGS) voltage tolerance of 12 V. Some
FETs can are designed to handle as much as 24 V between the drain and source terminals and this would
provide an increased safety margin for the pack design. Further, the DC current rating should be high enough to
safely handle sustained current in charge or discharge direction just below the maximum threshold tolerances of
the configured OCC and OCD protections and the lowest possible sense resistance value based on tolerance
and TCR considerations, or vice-versa. This ensures that there is sufficient power dissipation margin given a
worst case scenario for the fault detections. In addition, striving for minimal FET resistance at the expected gate
bias as well as lowest gate capacitance will help reduce conduction losses and increase power efficiency as well
as achieve faster turn-on and turn-off times for the FETs. Many of these FETs are now offered as dual, back-
back NFETs in wafer-chip scale (WCSP) packaging, decreasing both BOM count and shrinking necessary board
real estate to accommodate the components. Last, one should always refer to the safe operating area (SOA)
curves of the target FETs to ensure that the boundaries are never violated based on all possible load conditions
in the end application. The CSD83325L is an excellent example of a FET solution that meets all of the
aforementioned criteria, offering rDS(on) of 10.3 mΩ and VDS of 12 V with back-to-back NFETs in a chip-scale
package, a perfect fit for battery pack designs.
9.2.3.12 Additional ESD Protection Components
The additional capacitors placed across the CHG and DSF FET source pins as well as between PACK+ and
ground help to bolster and greatly improve the ESD robustness of the pack design. The former components
shunt damaging transients around the FETs and the latter components attempt to bypass such pulses to PACK–
before they couple further into the battery pack PCB. Two series capacitors are used for each of these protection
areas to prevent a battery short in the event of a single capacitor failure.
9.2.4 Application Curves
Figure 21. Overvoltage Protection Set and Clear
Figure 22. Undervoltage Protection Set and Clear




HTML 页

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41  42 


数据表 下载




链接网址

ALLDATASHEET是否为您带来帮助?  [ DONATE ]  

关于 Alldatasheet    |   广告服务   |   联系我们   |   隐私政策   |   书签   |   链接交换   |   制造商名单
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl