数据搜索系统,热门电子元器件搜索 |
|
EAST1608WA2 数据表(PDF) 10 Page - Everlight Electronics Co., Ltd |
|
EAST1608WA2 数据表(HTML) 10 Page - Everlight Electronics Co., Ltd |
10 / 11 page LifecyclePhase:Developing() LifecyclePhase: Revision : 1 Expired Period: Forever Release Date:2015-06-04 19:16:39.0 DATASHEET SMD B EAST1608WA2 10 Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 04-Jun-2015 Issue No: DSE-0013375 Rev.1 www.everlightamericas.com Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile P re -h e a tin g 1 5 0 ~ 2 0 0 °C 6 0 ~ 1 2 0 se c. A b o v e 2 1 7 °C 6 0 ~ 1 5 0 se c . 2 6 0 °C M a x . 1 0 sec . M a x . 6 °C /se c.M ax . A b o v e2 5 5 °C 3 0 sec .M a x . 3 °C /se c .M a x . 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. |
类似零件编号 - EAST1608WA2 |
|
类似说明 - EAST1608WA2 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |