数据搜索系统,热门电子元器件搜索 |
|
MC145442BP 数据表(PDF) 6 Page - LANSDALE Semiconductor Inc. |
|
MC145442BP 数据表(HTML) 6 Page - LANSDALE Semiconductor Inc. |
6 / 11 page www.lansdale.com Page 6 of 11 LANSDALE Semiconductor, Inc. ML145442, ML145443 GENERAL DESCRIPTION The ML145442 and ML145443 are full–duplex low–speed modems. They provide a 300–baud FSK signal for bidirectional data transmission over the telephone network. They can be operated in one of four basic configurations as determined by the state of MODE (pin 13) and LB (pin 2).The normal (non–loopback) and self test (loopback) modes in both answer and originate modes will be discussed. For an originate or channel 1 mode, a logic high level is placed on MODE (pin 13) and a logic low level is placed on LB (pin 2). In this mode, transmit data is input on TxD, where it is converted to a FSK signal and routed through a low–band band–pass filter. The filtered output signal is then buffered by the Tx op–amp line driver, which is capable of driving –9 dBm onto a 600Ω line. The receive signal is connected through a hybrid duplexer circuit on pins 15 and 16, RxA2 and RxA1. The signal then passes through the anti–alias- ing filter, the sample–and–hold circuit, is switched into the high–band band–pass filter, and then switched into the AC amplifi- er circuit. The output of the ac amplifier circuit is routed to the demodulator circuit and demodulated. The resulting digital data is then output through RxD (pin 5). The carrier detect circuit receives its signal from the output of the AC amplifier circuit and goes low when the incoming signal is detected (see Figure 4a). In the answer or channel 2 mode, a logic low level is placed on MODE (pin 13) and on LB (pin 2). In this mode, the data follows the same path except the FSK signal is routed to the high–band band–pass filter and the sample–and–hold signal is routed through the low–band band–pass filter (see Figure 4b). In the analog loopback originate or channel 1 mode, a logic high level is placed on MODE (pin 13) and on LB (pin 2). This mode is used for a self check of the modulator, demodulator, and low–band pass–band filter circuit. The modulator side is configured exactly like the originate mode above except the line driver output (TxA, pin 17) is switched to the negative input of the hybrid op–amp. The RxA2 input pin is open in this mode and the non–inverting input of the hybrid circuit is connected to VAG. The sample–and–hold out- put bypasses the filter so that the demodulator receives the modu- lated Tx data (see Figure 4c). This test checks all internal device components except the high–band band–pass filter, which can be checked in the answer or channel 2 mode test. In the analog loopback or channel 2 mode, a logic low level is placed on MODE (pin 13) and a logic high level on LB (pin 2). This mode is used for a self check of the modulator, demodulator, and high–band pass–band filter circuit. This configuration is exact- ly like the originate loopback mode above, except the signal is rout- ed through the high–band pass–band filter (see Figure 4d). Issue b |
类似零件编号 - MC145442BP |
|
类似说明 - MC145442BP |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |