数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

PI2127-EVAL1 数据表(PDF) 6 Page - Vicor Corporation

部件名 PI2127-EVAL1
功能描述  PI2127-EVAL1 60V/12A Full-Function High Side Active ORing
Download  9 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  VICOR [Vicor Corporation]
网页  http://www.vicorpower.com
标志 VICOR - Vicor Corporation

PI2127-EVAL1 数据表(HTML) 6 Page - Vicor Corporation

  PI2127-EVAL1 Datasheet HTML 1Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 2Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 3Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 4Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 5Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 6Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 7Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 8Page - Vicor Corporation PI2127-EVAL1 Datasheet HTML 9Page - Vicor Corporation  
Zoom Inzoom in Zoom Outzoom out
 6 / 9 page
background image
Picor Corporation • picorpower.com
PI2127-EVAL1 User Guide
Rev. 1.0
Page 6 of 9
4.10. D2 should be on.
This is due to a reverse
voltage fault condition caused by the bus
voltage being high with respect to the input
voltage (Vin2+).
4.11. Enable (turn on) PS2 output.
4.12. Verify that both PS1 and PS2 are sharing load
current evenly by looking at the supply current.
Power supplies output may need adjustment to
set current sharing between the supplies.
4.13. Disable (turn off) PS1, PS2, and PS3 outputs.
4.14. Enable (turn on) PS2 output then Enable and
PS3 outputs.
4.15. Verify that the electronic load voltage reading is
few millivolts below 48V. This verifies that the
PI2127-01-LGIZ
internal
MOSFET
is
in
conduction mode.
4.16. D2 should be off. This verifies that there is no
fault condition.
4.17. Verify that Vin1+ is low. This verifies that the
PI2127 (U1) internal FET is off.
4.18. D1 should be on.
This is due to a reverse
voltage fault condition caused by the bus
voltage being high with respect to the input
voltage (Vin1+).
Note: When the PI2127 internal MOSFET is in the on
state, it will not turn off unless a reverse current
greater than 0.75A is sensed in the MOSFET.
When both power supplies are enabled and both
PI2127 MOSFETs are in RDS(on); if one of the sources
(Power supplies) removed or disabled both PI2127
stay on unless the disabled power supply sources
current greater than 0.75A when turned off.
5.
Internal MOSFET RDS(on) Measurement:
5.1. The internal MOSFET RDS(on) can be measured
with a voltmeter between the S1 and D1 Kelvin
connection for U1 and between the S2 and D2
Kelvin connection for U2.
The potential
between S1 and D1 is the voltage drop across
the internal MOSFET and:
Where:
:
Voltage
drop
across
the
internal
MOSFET
:
Input current.
Note: The RDS(on) value is temperature dependent and the
junction
temperature
increases
directly
proportional to power dissipation.
6.
Input short circuit test:
PI2127 has a very fast response (80ns) to a reverse current
(Input short) fault condition. Measuring a short period
event requires attention to the test set-up. Before
proceeding, consider the following:
6.1. To emulate a real application, the BUS supplies
for this test should have a solid output source
such as a DC-DC converter that supplies high
current and can be connected very close to the
evaluation board to reduce stray parasitic
inductance.
Or use the prospective supply
sources of the end application where the PI2127
will be used. Typical bench power supplies have
slow response to output load change. In this test
when the power supply output is shorted and
then released, the bench power supply may
produce high output voltage with high current
capability that may damage the device under
test.
6.2. Do not install Input capacitors (C1 and/or C2) in
this test.
6.3. Output capacitor (C5) should be installed.
6.4. Place the scope probes very close to the PI2127 S
and D pins to measure Vin and Vout, and make
sure that the scope ground leads are very short.
You may use a close by ground pad for the scope
probe return, such as C1, C2, C3 and C4 return
pads.
6.5. Apply a short at one of the inputs (Vin1+ or
Vin2+) when both SIP’s (U1 and U2) are on, PS1
and PS2 are enabled. The short can be applied
electronically
using
a
MOSFET
connected
between Vin+ and Vin- or simply by connecting
Vin+ to Vin-. Then measure the response time
between when the short is applied and the
PI2127 internal MOSFET is disconnected (or
turned off). An example for the PI2127 response
time to an input short circuit is shown in Figure
4.


类似零件编号 - PI2127-EVAL1

制造商部件名数据表功能描述
logo
Vicor Corporation
PI2127-01-LGIZ VICOR-PI2127-01-LGIZ Datasheet
1Mb / 19P
   60 Volt, 12 Amp Full-Function Active ORing Solution
More results

类似说明 - PI2127-EVAL1

制造商部件名数据表功能描述
logo
Vicor Corporation
PI2126-EVAL1 VICOR-PI2126-EVAL1 Datasheet
916Kb / 8P
   PI2126-EVAL1 30V/12A Full-Function High Side Active ORing
PI2121-EVAL1 VICOR-PI2121-EVAL1 Datasheet
823Kb / 12P
   PI2121-EVAL1 Full-Function Active ORing
PI5101-EVAL1 VICOR-PI5101-EVAL1 Datasheet
1Mb / 12P
   PI5101-EVAL1 3.3V/60A High Side Active ORing
PI2001-EVAL1 VICOR-PI2001-EVAL1 Datasheet
659Kb / 11P
   PI2001-EVAL1 Active ORing
PI2007-EVAL1 VICOR-PI2007-EVAL1 Datasheet
1Mb / 10P
   PI2007-EVAL1 48V Bus High Side Active ORing
PI2003-EVAL1 VICOR-PI2003-EVAL1 Datasheet
554Kb / 8P
   PI2003-EVAL1 Active ORing
PI2161-EVAL1 VICOR-PI2161-EVAL1 Datasheet
860Kb / 8P
   PI2161-EVAL1 60V/12A High Side High Voltage Load Disconnect Switch
PI2002-EVAL1 VICOR-PI2002-EVAL1 Datasheet
777Kb / 11P
   PI2002-EVAL1 Active ORing With Load Disconnect
PI2127 VICOR-PI2127 Datasheet
1Mb / 19P
   60 Volt, 12 Amp Full-Function Active ORing Solution
PI2126 VICOR-PI2126 Datasheet
1Mb / 15P
   30 Volt, 12 Amp Full-Function Active ORing Solution
More results


Html Pages

1 2 3 4 5 6 7 8 9


数据表 下载

Go To PDF Page


链接网址




隐私政策
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com