数据搜索系统,热门电子元器件搜索 |
|
M02069 数据表(PDF) 6 Page - M/A-COM Technology Solutions, Inc. |
|
M02069 数据表(HTML) 6 Page - M/A-COM Technology Solutions, Inc. |
6 / 45 page M02069-12 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: http://www.macom.com/support 6 3.3 or 5 Volt VCSEL/FP Laser Driver IC for Applications to 4.3 Gbps Rev V2 1.4 AC Characteristics (VCC = 3.05 V to 3.55V or 4.7V to 5.5V, TA = -40 °C to +95 °C, unless otherwise noted) Typical values for common anode are at VCC = 3.3 V, IBOUTCA = 20 mA, IMOD = 20 mA, TA = 25 °C, unless otherwise noted. Typical values for common cathode are at VCC = 3.3 V, IBOUTCC = 5 mA, IMOD = 5 mA, TA = 25 °C, unless otherwise noted. VBH Bias_OK upper voltage threshold 1.45 1.6 1.7 V VFAULTL(4) Lower voltage threshold for fault inputs IBOUTCA, OUT+, CAPC, and MODSET FAIL asserts if any of these signals fall below this value. 300 400 mV VFAULTH(5) Upper voltage threshold for fault inputs IBOUTCC FAIL asserts if any of these signals fall above this value. 2.6 2.9 VCC3 - 0.2 V VSELFL Self bias voltage for IBOUTCA and OUT+ During disable state 0.5 1.65 2.0 V VSELFH Self bias voltage for IBOUTCC During disable state 0 1.25 V Notes: 1. Excludes bias and modulation currents. 2. Bias and modulation currents add directly to power supply current in 5V applications. The additional supply current noted excludes these currents. 3. VCC3 “supply OK” circuitry monitors the internally regulated 3.3V supply when VCC = 5V (VCC3SEL =low). When VCC = 3.3V, VCC3 “supply OK” circuitry monitors VCC (VCC3SEL =high). 4. A low level at IBOUTCA does not trigger a fault condition during common cathode operation. 5. A low level at IBOUTCC does not trigger a fault condition during common anode operation. Table 1-4. AC Characteristics Symbol Parameter Conditions Min. Typ. Max. Units. IMOD Modulation current adjust range Common Cathode Mode OUT+ and OUT- AC coupled into 50 Ω load. Common Anode Mode OUT+ and OUT- DC coupled into 25 Ω load.(1) 1 3 –15 45 mA IMOD(OFF)(2) Modulation current with output disabled DIS = high – – 150 µA Ratio of modulation current to MODMON current CCSEL = high, RLOAD = 50Ω CCSEL = low –30 65 –A/A IMOD-TC Programmable range for modulation current temperature coefficient Adjustable using TCSLOPE 0– 104 ppm/°C TTCSTART Temperature at which modulation current TC compensation enables 20 °C Table 1-3. DC Characteristics Symbol Parameter Conditions Min. Typ. Max. Units |
类似零件编号 - M02069_17 |
|
类似说明 - M02069_17 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |