数据搜索系统,热门电子元器件搜索 |
|
L6712D 数据表(PDF) 5 Page - STMicroelectronics |
|
L6712D 数据表(HTML) 5 Page - STMicroelectronics |
5 / 27 page 5/27 L6712A L6712 PIN FUNCTION N. (*) Name Description SO VFQFPN 1 33 LGATE1 Channel 1 LS driver output. A little series resistor helps in reducing device-dissipated power. 2 34 VCCDR LS drivers supply: it can be varied from 5V to 12V buses. Filter locally with at least 1 µF ceramic cap vs. PGND. 3 35 PHASE1 Channel 1 HS driver return path. It must be connected to the HS1 mosfet source and provides the return path for the HS driver of channel 1. 4 36 UGATE1 Channel 1 HS driver output. A little series resistor helps in reducing device-dissipated power. 5 2 BOOT1 Channel 1 HS driver supply. This pin supplies the relative high side driver. Connect through a capacitor (100nF typ.) to the PHASE1 pin and through a diode to VCC (cathode vs. boot). 6 4 VCC Device supply voltage. The operative supply voltage is 12V ±10%. Filter with 1 µF (Typ.) capacitor vs. GND. 7 5,6 SGND All the internal references are referred to this pin. Connect it to the PCB signal ground. 8 7 COMP This pin is connected to the error amplifier output and is used to compensate the control feedback loop. 9 8 FB This pin is connected to the error amplifier inverting input and is used to compensate the control feedback loop. 10 9 DROOP A current proportional to the sum of the current sensed in both channel is sourced from this pin (50 µA at full load, 70µA at the Constant Current threshold). Short to FB to implement the Droop effect: the resistor connected between FB and VSEN (or the regulated output) allows programming the droop effect. Otherwise, connect to GND directly or through a resistor (43k Ω max) and filter with 1nF capacitor. In this last case, current information can be used for other purposes. 11 11 REF_IN / OUT Reference input/output. Filter vs. GND with 1nF ceramic capacitor (a total of 100nF capacitor is allowed). It reproduces the reference used for the regulation following VID code: when VID=111, the reference for the regulation must be connected on this pin. References ranging from 0.800V up to 3.300V can be accepted. 12 12 VSEN Connected to the output voltage it is able to manage Over & Under-voltage conditions and the PGOOD signal. It is internally connected with the output of the Remote Sense Amplifier for Remote Sense of the regulated voltage. Connecting 1nF capacitor max vs. GND can help in reducing noise injection at this pin. If no Remote Sense is implemented, connect it directly to the regulated voltage in order to manage OVP, UVP and PGOOD. 13 13 ISEN1 Channel 1 current sense pin. The output current may be sensed across a sense resistor or across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain or to the sense resistor through a resistor Rg. The net connecting the pin to the sense point must be routed as close as possible to the PGNDS net in order to couple in common mode any picked-up noise. 14 14 PGNDS1 Channel 1 Power Ground sense pin. The net connecting the pin to the sense point must be routed as close as possible to the ISEN1 net in order to couple in common mode any picked-up noise. 15 15 PGNDS2 Channel 2 Power Ground sense pin. The net connecting the pin to the sense point must be routed as close as possible to the ISEN2 net in order to couple in common mode any picked-up noise. |
类似零件编号 - L6712D |
|
类似说明 - L6712D |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |