数据搜索系统,热门电子元器件搜索 |
|
MC10H115 数据表(PDF) 2 Page - ON Semiconductor |
|
MC10H115 数据表(HTML) 2 Page - ON Semiconductor |
2 / 5 page MC10H115 www.onsemi.com 2 Figure 1. Logic Diagram Figure 2. Pin Assignment VCC1 Aout Bout Ain Ain Bin Bin VEE VCC2 Dout Cout Din Din Cin Cin VBB 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 2 5 4 3 6 7 14 11 10 15 12 13 9 *VBB to be used to supply bias to the MC10H115 only and bypassed (when used) with 0.01 mF to 0.1 mF capacitor to ground (0 V). VBB can source < 1.0 mA. When input pin with bubble goes positive its respective output pin with bubble goes positive. VBB* VCC1 = Pin 1 VCC2 = Pin 16 VEE = Pin 8 Pin assignment is for Dual-in-Line Package. Table 1. MAXIMUM RATINGS Symbol Characteristic Rating Unit VEE Power Supply (VCC = 0) −8.0 to 0 Vdc VI Input Voltage (VCC = 0) 0 to VEE Vdc Iout Output Current Continuous Surge 50 100 mA TA Operating Temperature Range 0 to +75 °C Tstg Storage Temperature Range Plastic Ceramic −55 to +150 −55 to +165 °C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Table 2. ELECTRICAL CHARACTERISTICS (VEE = −5.2 V ±5%) (Note 2) 0° 25° 75° Symbol Characteristic Min Max Min Max Min Max Unit IE Power Supply Current − 29 − 26 − 29 mA IinH Input Current High − 150 − 95 − 95 mA ICBO Input Leakage Current − 1.5 − 1.0 − 1.0 mA VBB Reference Voltage −1.38 −1.27 −1.35 −1.25 −1.31 −1.19 Vdc VOH High Output Voltage −1.02 −0.84 −0.98 −0.81 −0.92 −0.735 Vdc VOL Low Output Voltage −1.95 −1.63 −1.95 −1.63 −1.95 −1.60 Vdc VIH High Input Voltage (Note 1) −1.17 −0.84 −1.13 −0.81 −1.07 −0.735 Vdc VIL Low Input Voltage (Note 1) −1.95 −1.48 −1.95 −1.48 −1.95 −1.45 Vdc VCMR Common Mode Range (Note 3) − − −2.85 to −0.8 − − Vdc VPP Input Sensitivity (Note 4) − − 150 typ − − mVPP 1. When VBB is used as the reference voltage. 2. Each MECL 10H™ series circuit has been designed to meet the specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50 W resistor to −2.0 V. 3. Differential input not to exceed 1.0 Vdc. 4. 150 mVp−p differential input required to obtain full logic swing on output. |
类似零件编号 - MC10H115_16 |
|
类似说明 - MC10H115_16 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |