数据搜索系统,热门电子元器件搜索 |
|
TDA2SGBRQABCQ1 数据表(PDF) 11 Page - Texas Instruments |
|
|
TDA2SGBRQABCQ1 数据表(HTML) 11 Page - Texas Instruments |
11 / 426 page 11 TDA2SX, TDA2SG TDA2HG, TDA2HV, TDA2LF www.ti.com SPRS951A – DECEMBER 2015 – REVISED APRIL 2016 Submit Documentation Feedback Product Folder Links: TDA2SX TDA2SG TDA2HG TDA2HV TDA2LF Terminal Configuration and Functions Copyright © 2015–2016, Texas Instruments Incorporated – D = Open drain – DS = Differential Signaling – A = Analog – PWR = Power – GND = Ground – CAP = LDO Capacitor 7. BALL RESET STATE: The state of the terminal at power-on reset: – drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated) – drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated) – OFF: High-impedance – PD: High-impedance with an active pulldown resistor – PU: High-impedance with an active pullup resistor 8. BALL RESET REL. STATE: The state of the terminal at the deactivation of the rstoutn signal (also mapped to the PRCM SYS_WARM_OUT_RST signal) – drive 0 (OFF): The buffer drives VOL (pulldown or pullup resistor not activated) – drive clk (OFF): The buffer drives a toggling clock (pulldown or pullup resistor not activated) – drive 1 (OFF): The buffer drives VOH (pulldown or pullup resistor not activated) – OFF: High-impedance – PD: High-impedance with an active pulldown resistor – PU: High-impedance with an active pullup resistor NOTE For more information on the CORE_PWRON_RET_RST reset signal and its reset sources, see the Power Reset and Clock Management / PRCM Reset Management Functional Description section of the Device TRM. 9. RESET REL. MUXMODE: This muxmode is automatically configured at the release of the rstoutn signal (also mapped to the PRCM SYS_WARM_OUT_RST signal). 10. IO VOLTAGE VALUE: This column describes the IO voltage value (VDDS supply). 11. POWER: The voltage supply that powers the terminal IO buffers. 12. HYS: Indicates if the input buffer is with hysteresis: – Yes: With hysteresis – No: Without hysteresis An empty box means "Yes". NOTE For more information, see the hysteresis values in Section 5.7, Electrical Characteristics. 13. BUFFER TYPE: Drive strength of the associated output buffer. NOTE For programmable buffer strength: – The default value is given in Table 4-2. – A note describes all possible values according to the selected muxmode. 14. PULLUP / PULLDOWN TYPE: Denotes the presence of an internal pullup or pulldown resistor. Pullup and pulldown resistors can be enabled or disabled via software. 15. DSIS: The deselected input state (DSIS) indicates the state driven on the peripheral input (logic "0" or logic "1") when the peripheral pin function is not selected by any of the PINCNTLx registers. – 0: Logic 0 driven on the peripheral's input signal port. – 1: Logic 1 driven on the peripheral's input signal port. |
类似零件编号 - TDA2SGBRQABCQ1 |
|
类似说明 - TDA2SGBRQABCQ1 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |