数据搜索系统,热门电子元器件搜索 |
|
TS30011-M025 数据表(PDF) 4 Page - Semtech Corporation |
|
TS30011-M025 数据表(HTML) 4 Page - Semtech Corporation |
4 / 18 page TS30011/12/13 Final Datasheet Rev 1.7 August 24, 2015 www.semtech.com 4 of 18 Semtech Absolute Maximum Ratings Thermal Characteristics Recommended Operating Conditions Over operating free–air temperature range unless otherwise noted(1, 2) Parameter Value Units VCC -0.3 to 26.4 (-0.3 to 20 for TS30013) V BST -0.3 to (VCC+6) V VSW -1 to 26.4 (-1 to 20 for TS30013) V EN, PG,FB -0.3 to 6 V Electrostatic Discharge – Human Body Model +/-2k V Electrostatic Discharge – Charge Device Model +/-500 V Lead Temperature (soldering, 10 seconds) 260 O C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to network ground terminal. Parameter Symbol Value Units Thermal Resistance Junction to Air (Note 1) θ JA 34.5 O C/W Thermal Resistance Junction to Case (Note 1) θ JC 2.5 O C/W Storage Temperature Range T STG -65 to 150 O C Maximum Junction Temperature T J MAX 150 O C Operating junction Temperature Range T J -40 to 125 O C Note 1: Assumes 16LD 3x3 QFN with hi-K JEDEC board and 13.5 inch2 of 1 oz Cu and 4 thermal vias connected to PAD Parameter Symbol Min Type Max Units Input Operating Voltage VCC 4.5 12 24 (18 for TS30013) V Bootstrap Capacitor C BST 15 22 200 nF Output Filter Inductor Typical Value (Note 1) L OUT 3.76 4.7 5.64 uH Output Filter Capacitor Typical Value (Note 2) C OUT 33 44 (2 x 22) uF Output Filter Capacitor ESR C OUT-ESR 2 100 mΩ Input Supply Bypass Capacitor Typical Value (Note 3) C BYPASS 8 10 uF Note 1: For best performance, an inductor with a saturation current rating higher than the maximum VOUT load requirement plus the inductor current ripple. Note 2: For best performance, a low ESR ceramic capacitor should be used. Note 3: For best performance, a low ESR ceramic capacitor should be used. If CBYPASS is not a low ESR ceramic capacitor, a 0.1uF ceramic capacitor should be added in parallel to CBYPASS |
类似零件编号 - TS30011-M025 |
|
类似说明 - TS30011-M025 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |