数据搜索系统,热门电子元器件搜索 |
|
LMZ31506EVM-692 数据表(PDF) 5 Page - Texas Instruments |
|
LMZ31506EVM-692 数据表(HTML) 5 Page - Texas Instruments |
5 / 22 page www.ti.com TEST SET-UP 4 TEST SET-UP This section describes how to properly set-up and use the LMZ3150xEVM-692 evaluation module. 4.1 Input/Output Connections The LMZ3150xEVM-692 is provided with input/output connectors and test points as shown in Table 4. A power supply capable of supplying 4 A must be connected to J1 through a pair of 20 AWG wires. The jumper across J3 must be in place. See Section 3.6 for split input voltage rail operation. The load must be connected to J7 through a pair of 20 AWG wires. The maximum load current capability must be 6 A. Wire lengths must be minimized to reduce losses in the wires. Test-point TP1 provides a place to monitor the V IN input voltages with TP2 providing a convenient ground reference. TP4 is used to monitor the output voltage with TP12 as the ground reference. Table 4. EVM Connectors and Test Points REF DES LABEL DESCRIPTION J1 PVIN Primary VIN connector J2 VBIAS VBIAS input voltage input connector J3 VIN Jumper used to connect VIN to PVIN. EVM default setting connects VIN to PVIN. J7 VOUT VOUT connector J4 VADJ VOUT selection. Default VOUT is 3.3 V. J11 FREQ Switching frequency selection. Default frequency is 630 kHz. J6 TR_IN TRACK IN connector. J5 provides two divider settings. J5 SS_TR Track voltage select jumper. Used with J6. J9 INH_UVLO Enable jumper. Install shunt to inhibit the power supply. J8 INH_UVLO Selects UVLO for power supply turn on. Default setting is for 8-V UVLO. J10 STSEL Internal slow start select jumper. Install shunt for internal slow start. TP1 PVIN PVIN circuit point TP3 VBIAS VBIAS circuit point TP6 VIN VIN circuit point TP4 VOUT VOUT circuit point TP2, TP12 GND Power grounds TP15 AGND Analog ground TP7 TR_IN Track input TP8 SS_TR Tracking input after divider TP9 PWRGD Power good status TP14 RT/CLK SYNC input TP10 COMP Error amplifier output TP13 PH Switch node TP11 INH_UVLO Inhibit and UVLO input VOUT remote sense node connected to J7 pin 2. TP5 can be used for measuring the loop TP5 SENSE+ response along with changing R1 to 49.9 Ω. 5 SNVU295 – JULY 2013 LMZ31506H, LMZ31503 and LMZ31506 Simple Switcher® Power Module Evaluation Module Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated |
类似零件编号 - LMZ31506EVM-692 |
|
类似说明 - LMZ31506EVM-692 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |