数据搜索系统,热门电子元器件搜索 |
|
LA4815VH 数据表(PDF) 6 Page - ON Semiconductor |
|
LA4815VH 数据表(HTML) 6 Page - ON Semiconductor |
6 / 15 page LA4815VH No.A1374-6/15 Notes on Using the IC 1. Voltage gain settings (Pins 4 and 11) The voltage gain of the power amplifier is fixed by the internal resistors. • Pins 4 and 11 be left open : Approximately 26dB • Pins 4 and 11 connected to GND : Approximately 39.5dB Note that the voltage gain can be changed using two resistors. (See Fig. 1) • Voltage gain setting : According to the resistor connected between Pin 4 and Pin 12 (GND1) * Voltage gain = 20log (20 × (625 + Rvg1)/(125 + Rvg1)) • Output DC voltage setting : According to the resistor connected between Pin 11 and Pin 12 (GND1) * Rvg1 = Rvg2 must be satisfied. In addition, the voltage gain can also be lowered to approximately 20dB (when using 5V or 6V power supply) by an application such as shown in Fig. 2 below. • Voltage gain setting : According to the resistor connected between Pin 4 and Pin 1 (OUT) * Voltage gain = 20log (20 × (125 + Rvg3)/(10,125 + Rvg3)) • Output DC voltage setting : According to the resistor connected between Pin 11 and Pin 2 (VCC) * Set the resistor values so that the Pin 5 (OUT) DC voltage is approximately half the supply voltage. Example : When Rvg3 = 10kΩ, Rvg4 = 22kΩ(when VCC = 6V) However, note that using this method to greatly lower the voltage gain deteriorates the characteristics, so the voltage gain should be lowered only to approximately 20dB. In addition, when using a high supply voltage (7V or more), the clipped waveform may invert, so this voltage gain reduction method must not be used in these cases. Figure 1 Figure 2 2. Signal source impedance : rg As mentioned above, since the input coupling capacitor Cin affects the ripple rejection ratio, the signal source impedance value rg, which is associated with this capacitor, also affects the ripple rejection ratio, so rg should be as small as possible. Therefore, when attenuating the signal at the Cin front end as shown in Fig. 4, the constants should be set in consideration of these characteristics. Using the smallest resistor Rg1 value possible is recommended. In addition, when setting the signal level, the voltage gain should be set on the LA4815VH side and the input front-end should be configured using only the input coupling capacitor, Cin, as shown in Fig. 5 in order to maximize the ripple rejection ratio. Figure 4 Figure 3 Figure 5 LA4815VH Rvg2 Rvg1 GAIN2 OUT VCC GND1 GAIN1 LA4815VH Rvg4 Rvg3 GAIN2 OUT VCC GND1 GAIN1 1 2 4 12 11 1 2 4 12 11 Vbias 100k Ω + - Pre-Amp Rg2 Cin Rg1 rg other IC ro LA4815VH Cin other IC ro LA4815VH Cin IN OUT IN 13 13 OUT IN 13 |
类似零件编号 - LA4815VH |
|
类似说明 - LA4815VH |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |