数据搜索系统,热门电子元器件搜索 |
|
TS80C188EB25 数据表(PDF) 11 Page - Intel Corporation |
|
TS80C188EB25 数据表(HTML) 11 Page - Intel Corporation |
11 / 59 page 80C186EB80C188EB 80L186EB80L188EB Table 3 Pin Descriptions (Continued) Pin Pin Input Output Description Name Type Type States A1816 IO A(L) H(Z) These pins provide multiplexed Address during the address phase of the bus cycle Address bits 16 through 19 are presented A19ONCE R(WH) on these pins and can be latched using ALE These pins are (A15A8) P(X) driven to a logic 0 during the data phase of the bus cycle On the (A1816) 80C188EB A15 – A8 provide valid address information for the (A19ONCE) entire bus cycle During a processor reset (RESIN active) A19 ONCE is used to enable ONCE mode A1816 must not be driven low during reset or improper operation may result S20 O H(Z) Bus cycle Status are encoded on these pins to provide bus transaction information S20 are encoded as follows R(Z) P(1) S2 S1 S0 Bus Cycle Initiated 0 0 0 Interrupt Acknowledge 0 0 1 Read IO 0 1 0 Write IO 0 1 1 Processor HALT 1 0 0 Queue Instruction Fetch 1 0 1 Read Memory 1 1 0 Write Memory 1 1 1 Passive (no bus activity) ALE O H(0) Address Latch Enable output is used to strobe address information into a transparent type latch during the address phase R(0) of the bus cycle P(0) BHE O H(Z) Byte High Enable output to indicate that the bus cycle in progress is transferring data over the upper half of the data bus BHE and (RFSH) R(Z) A0 have the following logical encoding P(X) A0 BHE Encoding (for the 80C186EB80L186EB only) 0 0 Word Transfer 0 1 Even Byte Transfer 1 0 Odd Byte Transfer 1 1 Refresh Operation On the 80C188EB80L188EB RFSH is asserted low to indicate a refresh bus cycle RD O H(Z) ReaD output signals that the accessed memory or IO device must drive data information onto the data bus R(Z) P(1) WR O H(Z) WRite output signals that data available on the data bus are to be written into the accessed memory or IO device R(Z) P(1) READY I A(L) READY input to signal the completion of a bus cycle READY must be active to terminate any bus cycle unless it is ignored by S(L) correctly programming the Chip-Select Unit DEN O H(Z) Data ENable output to control the enable of bi-directional transceivers in a buffered system DEN is active only when data is R(Z) to be transferred on the bus P(1) NOTE Pin names in parentheses apply to the 80C188EB80L188EB 11 11 |
类似零件编号 - TS80C188EB25 |
|
类似说明 - TS80C188EB25 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |