数据搜索系统,热门电子元器件搜索 |
|
HCPL-0302 数据表(PDF) 8 Page - AVAGO TECHNOLOGIES LIMITED |
|
HCPL-0302 数据表(HTML) 8 Page - AVAGO TECHNOLOGIES LIMITED |
8 / 15 page 8 Package Characteristics Parameter Symbol Min. Typ. Max. Units Test Conditions Fig. Note Input-Output Momentary VISO 3750 Vrms TA = 25°C, RH < 50% 8, 9 Withstand Voltage Input-Output Resistance RI-O 1012 Ω VI-O = 500 V 9 Input-Output Capacitance CI-O 0.6 pF Freq = 1 MHz Notes: 1. Derate linearly above 70°C free air temperature at a rate of 0.3 mA/°C. 2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak minimum = 0.2 A. See Application section for additional details on limiting IOL peak. 3. Derate linearly above 85°C, free air temperature at the rate of 4.0 mW/°C. 4. Input power dissipation does not require derating. 5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%. 6. In this test, VOH is measured with a DC load current. When driving capacitive load VOH will approach VCC as IOH approaches zero amps. 7. Maximum pulse width = 1 ms, maximum duty cycle = 20%. 8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage >4500 Vrms for 1 second (leakage detec- tion current limit II-O < 5 µA). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable. 9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together. 10. PDD is the difference between tPHL and tPLH between any two parts or channels under the same test conditions. 11. Common mode transient immunity in the high state is the maximum tolerable |dVCM/dt| of the common mode pulse VCM to assure that the output will remain in the high state (i.e. VO > 6.0 V). 12. Common mode transient immunity in a low state is the maximum tolerable |dVCM/dt| of the common mode pulse,VCM, to assure that the output will remain in a low state (i.e. VO < 1.0 V). 13. This load condition approximates the gate load of a 1200 V/20 A IGBT. 14. The power supply current increases when operating frequency and Cg of the driven IGBT increases. Figure 1. VOH vs. temperature. Figure 2. VOH vs. IOH. Figure 3. VOL vs. temperature. -50 -2.5 TA – TEMPERATURE – C 125 -25 0 0 25 75 100 50 -2.0 -1.5 -1.0 -0.5 0 IOH – OUTPUT HIGH CURRENT – A 0 0.2 0.4 -4 -3 -1 -2 -50 0.39 TA – TEMPERATURE – C 125 -25 0.44 0 25 75 100 50 0.40 0.41 0.42 0.43 |
类似零件编号 - HCPL-0302 |
|
类似说明 - HCPL-0302 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |