数据搜索系统,热门电子元器件搜索 |
|
ISL3150EIBZ 数据表(PDF) 9 Page - Intersil Corporation |
|
ISL3150EIBZ 数据表(HTML) 9 Page - Intersil Corporation |
9 / 22 page 9 FN6363.2 July 30, 2009 Receiver Skew | tPLH - tPHL |tSKD (Figure 5) Full - 2.5 5 ns Receiver Enable to Output Low tZL RL = 1kΩ, CL = 15pF, SW = VCC (Figure 6), (Note 10) Full - 8 15 ns Receiver Enable to Output High tZH RL = 1kΩ, CL = 15pF, SW = GND (Figure 6), (Note 10) Full - 7 15 ns Receiver Disable from Output Low tLZ RL = 1kΩ, CL = 15pF, SW = VCC (Figure 6) Full - 8 15 ns Receiver Disable from Output High tHZ RL = 1kΩ, CL = 15pF, SW = GND (Figure 6) Full - 8 15 ns Time to Shutdown tSHDN (Note 11) Full 60 160 600 ns Receiver Enable from Shutdown to Output High tZH(SHDN) RL = 1kΩ, CL = 15pF, SW = GND (Figure 6), (Notes 11, 13) Full - - 200 ns Receiver Enable from Shutdown to Output Low tZL(SHDN) RL = 1kΩ, CL = 15pF, SW = VCC (Figure 6), (Notes 11, 13) Full - - 200 ns NOTES: 6. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. 7. Supply current specification is valid for loaded drivers when DE = 0V. 8. Applies to peak current. See “Typical Performance Curves” beginning on page 14 for more information. 9. Keep RE = 0 to prevent the device from entering SHDN. 10. The RE signal high time must be short enough (typically <100ns) to prevent the device from entering SHDN. 11. Transceivers are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 60ns, the parts are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low Power Shutdown Mode” on page 13. 12. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN. 13. Set the RE signal high time >600ns to ensure that the device enters SHDN. 14. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 15. See Figure 8 for more information, and for performance over-temperature. 16. Tested according to TIA/EIA-485-A, Section 4.2.6 (±100V for 15µs at a 1% duty cycle). 17. Limits established by characterization and are not production tested. Test Circuits and Waveforms FIGURE 1A. VOD AND VOC FIGURE 1B. VOD WITH COMMON MODE LOAD FIGURE 1. DC DRIVER TEST CIRCUITS Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA =+25°C (Note6). Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) PARAMETER SYMBOL TEST CONDITIONS TEMP (°C) MIN (Note 14) TYP MAX (Note 14) UNITS D DE DI VCC VOD VOC RL/2 RL/2 Z Y D DE DI VCC VOD 375Ω 375Ω Z Y RL = 60Ω VCM -7V TO +12V ISL3150E, ISL3152E, ISL3153E, ISL3155E, ISL3156E, ISL3158E |
类似零件编号 - ISL3150EIBZ |
|
类似说明 - ISL3150EIBZ |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |