数据搜索系统,热门电子元器件搜索 |
|
LM25085QMYE 数据表(PDF) 11 Page - Texas Instruments |
|
LM25085QMYE 数据表(HTML) 11 Page - Texas Instruments |
11 / 30 page RT Input Voltage STOP RUN LM25085 RT VIN RT = VOUT x 6 x 10 6 FS - 8.6 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 To set a specific continuous conduction mode switching frequency (FS), the RT resistor is determined from the following: where • RT is in kΩ (5) A simplified version of Equation 5 at VIN = 12V, and tD = 100ns, is: For VIN = 42V and tD = 100ns, the simplified equation is: SHUTDOWN The LM25085 can be shutdown by grounding the RT pin (see Figure 25). In this mode the PFET is held off, and the VCC regulator is disabled. The internal operating current is reduced to the value shown in Figure 6. The shutdown threshold at the RT pin is ≊0.73V, with ≊50mV of hysteresis. Releasing the pin enables normal operation. The RT pin must not be forced high during normal operation. Figure 25. Shutdown Implementation CURRENT LIMITING The LM25085 current limiting operates by sensing the voltage across either the RDS(ON) of Q1, or a sense resistor, during the on-time and comparing it to the voltage across the resistor RADJ (see Figure 26). The current limit function is much more accurate and stable over temperature when a sense resistor is used. The RDS(ON) of a MOSFET has a wide process variation and a large temperature coefficient. If the voltage across RDS(ON) of Q1, or the sense resistor, is greater than the voltage across RADJ, the current limit comparator switches to turn off Q1. Current sensing is disabled for a blanking time of ≊100ns at the beginning of the on-time to prevent false triggering of the current limit comparator due to leading edge current spikes. Because of the blanking time and the turn-on and turn-off delays created by the PFET, the on-time at the PGATE pin should not be set less than 150ns. An on-time shorter than that may prevent the current limit detection circuit from properly detecting an over-current condition. The duration of the subsequent forced off-time is a function of the input voltage and the voltage at the FB pin, as shown in Figure 10. The longer-than-normal forced off-time allows the inductor current to decrease to a low level before the next on-time. This cycle-by-cycle monitoring, followed by a forced off-time, provides effective protection from output load faults over a wide range of operating conditions. The voltage across the RADJ resistor is set by an internal 40µA current sink at the ADJ pin. When using Q1’s RDS(ON) for sensing, the current at which the current limit comparator switches is calculated from: ICL = 40µA x RADJ/RDS(ON) (6) When using a sense resistor (RSEN) the threshold of the current limit comparator is calculated from: Copyright © 2008–2013, Texas Instruments Incorporated Submit Documentation Feedback 11 Product Folder Links: LM25085 LM25085-Q1 |
类似零件编号 - LM25085QMYE |
|
类似说明 - LM25085QMYE |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |