数据搜索系统,热门电子元器件搜索 |
|
KA3504 数据表(PDF) 4 Page - Fairchild Semiconductor |
|
KA3504 数据表(HTML) 4 Page - Fairchild Semiconductor |
4 / 12 page KA3504 4 Pin Definitions Pin No. Name Pin Function Description 1VS33 Over Voltage Protection Input for the 3.3V. It Directly Senses the 3.3V Rail Without any External Divider. 2VS5 Over Voltage Protection Input for the 5V. It Directly Senses the 5V Rail Without any External Divider. 3VS12 Over Voltage Protection Input for the 12V. It Directly Senses the 12V Rail Without any External Divider. 4PGI Power Good Signal Generator Input. It Should be Supplied From a Bulk Dependent Voltage in Order to Detect Power on and off State. 5VCC Supply Voltage. Its Recommended Operating Voltage is Ranged from 15V to 30V. 6FPO Fault Protection Output (Open Collector Output). This Pin Indicates the Fault Condition. When Fault State Occurs, the PGO Signal Goes Low. Normal = ’Low", Fault = "High". 7PSON Remote on/off Input. It does TTL Operation and its Threshold Voltage is 1.4V. In Case of Open Circuit, the Voltage at this Pin is High (5.0V). If PSON = "Low", then FPO = "Low". It Means the Main SMPS is Working. When PSON = "High or Open", then FPO = "High" and the main SMPS Stops to Work. 8TPSON Timing pin for PSON Delay. Ton/Toff=8ms/24ms (Typ.) with Cpson=0.1 µF Externally. PSON On Delay Time (Ton) is Measured as PSON Input Goes Low to High. PSON Off Delay Time (Toff) can be Measured Reversely. 9PGO Power Good Output Signal (Open Collector). PGO = "High" means "Power Good" for Operation and PGO = "Low" Means "Power Fail". 10 TPG Timing pin for PGO delay. TPG = 270ms (Typ.) with CPG = 2.2 µF Externally. The High/low Threshold Voltages are 1.8V/0.6V and the Voltage of pin10 Would be Charged up to 2.9V for Noise Margin. 11 RI OCP Current Sense Setting pin. The Reference Voltage at this pin is set to 1.25V Internally.You can fix the OCP Reference Current by Using RI Resistor. 12 GND Ground 13 TPROT Timing pin for Under Voltage Protection and Over Current Protection Blank-out time. Its Threshold Voltage is 1.8V and Clamped at 2.9V After full Charging. Target of Delay Time is 38ms and it is Realized Through External Capacitor (C=0.47 µF). 14 IS12 Current Sense Input for +12V. This pin is Connected to the Current Sensing Resistor or Inductor. You can Define OCP Offset Voltage for +12V by Using RI Resistor Externally. If you Connected RI Resistor of 62k Ω at Pin11 to Ground, the Reference Current(Iref) Should be 20 µA. After that, you can Make a Constant OCP Offset Voltage (VOFFSET = RO × 5 × Iref). In Case the Voltage Drop (=IO.12 × RS) of the Sense Resistor or Inductor is Larger than Offset Voltage, FPO Becomes "High" After Some Delay time and the Main SMPS is Turned-off. So the Over Current level is Determined by Following Equation. (IO.12 = VOFFSET/ RS) ∗ See Application Note for Details. 15 IS5 Current Sense Input for +5V. You can Make the +5V OCP Function as Previous Method in IS12 (Pin14). 16 IS33 Current Sense Input for +3.3V. You can also Make the +3.3V OCP Function as Previous Method in IS12 (Pin14). |
类似零件编号 - KA3504 |
|
类似说明 - KA3504 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |