数据搜索系统,热门电子元器件搜索 |
|
AD7482AST 数据表(PDF) 8 Page - Analog Devices |
|
AD7482AST 数据表(HTML) 8 Page - Analog Devices |
8 / 16 page REV. 0 –8– AD7482 220 BIAS VOLTAGE 1 2 3 4 5 6 7 8 AD8021 50 AC SIGNAL 220 10pF –VS +VS – + VIN 10pF Figure 2. Analog Input Circuit Used for 1 MHz Input Tone For higher input bandwidth applications, Analog Devices’ AD8021 op amp (also available as a dual AD8022) is the recommended choice to drive the AD7482. Figure 2 shows the analog input circuit used to obtain the data for the FFT plot shown in TPC 2. A bipolar analog signal is applied to the terminal shown and biased up with a stable, low noise dc voltage connected as shown. A 10 pF compensation capacitor is connected between Pin 5 of the AD8021 and the negative supply. As with the previous circuit, the AD8021 is supplied with +12 V and –12 V supplies. The supply pins are decoupled as close to the device as possible, with both a 0.1 µF and 10 µF capacitor connected to each pin. In each case, the 0.1 µF capaci- tor should be the closer of the two caps to the device. The AD8021 logic reference pin is tied to analog ground and the DISABLE Pin is tied to the positive supply as shown. Detailed information on the AD8021 is available on the Analog Devices website. FREQUENCY – kHz –20 10 100 –50 –70 –80 –40 1000 –30 –60 –10 0 100mV p-p SINE WAVE ON SUPPLY PINS TPC 7. PSRR without Decoupling 1 2 3 4 5 6 7 8 AD829 1k 1k 100 AC SIGNAL BIAS VOLTAGE 150 220pF –VS +VS – + VIN Figure 1. Analog Input Circuit Used for 10 kHz Input Tone Figure 1 shows the analog input circuit used to obtain the data for the FFT plot shown in TPC 1. The circuit uses an Analog Devices AD829 op amp as the input buffer. A bipolar analog signal is applied as shown and biased up with a stable, low noise dc voltage connected to the labeled terminal shown. A 220 pF compensation capacitor is connected be- tween Pin 5 and the AD829 and the analog ground plane. The AD829 is supplied with +12 V and –12 V supplies. The supply pins are decoupled as close to the device as possible with both a 0.1 F and 10 F capacitor connected to each pin. In each case, 0.1 F capacitor should be the closer of the two caps to the device. More information on the AD829 is available on the Analog Devices website. TEMPERATURE – C 0.0004 –55 –25 5 35 95 125 –0.0004 –0.0008 –0.0012 –0.0016 –0.0020 0 65 TPC 8. Reference Out Error |
类似零件编号 - AD7482AST |
|
类似说明 - AD7482AST |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |