数据搜索系统,热门电子元器件搜索 |
|
TDA4605-2 数据表(PDF) 8 Page - Siemens Semiconductor Group |
|
TDA4605-2 数据表(HTML) 8 Page - Siemens Semiconductor Group |
8 / 20 page Semiconductor Group 61 TDA 4605-2 If the voltage level of the rectified mains voltage is reduced strongly under the influence of the applied load it can happen that V3 is below the voltage level V3A - please refer to the time t3 in the diagram. This is because if an attempt is made to start the SMPS with a too low mains voltage. The internal primary voltage monitor circuit then clamps the voltage V3 to the voltage level V3S until the IC switches off ( V6 < V6A). After this a new attempt to start the SMPS will begin at the time t1 in the diagram. Control Range, Overload and No-Load Behaviour After the IC has started, it is operating in the control range. The voltage level at pin 1 is typically 400 mV. The gain of the control circuit consist of two parts: at first a fixed proportional part which is internally fixed and an integrating part which can be set by means of the external capacitor at pin 7. If the load is applied to the output of the SMPS, the control and overload amplifier allows wider pulses ( V5 = "H") .The peak voltage value at pin 2 increases up to V2S max . If the secondary load is increased further the overload amplifier begins to reduce the pulse width of the output pulse. This point is referred to as the fold-back point of the power supply. Because of the fact that the IC supply voltage is directly proportional to the secondary voltage, the supply voltage V6 will be reduced according to the behaviour of the control circuit under the overload condition. If V6 falls below the value V6 min , the IC will operate in the burst mode. Because of the large time constant of the start- up circuit which is operating with half-wave rectification, only a small output power is transferred into the load during the secondary short-circuit of the SMPS. The overload amplifier reduces the output pulse width down to the pulse width tpk . This pulse width must remain possible in order to permit the IC to start up without problems from the virtual short-circuit, which every switching on with V1 =0 is representing. If no load is applied to the secondary side, the output pulses ( V5 = H) become shorter. If the pulse width is reduced be low a certain internal limit the IC will suppress some of the output pulses. If the load is reduced further because of the decreasing duty cycle the measurement error of the rectifier network ( R8 , D3, C6 of the application circuit) is increasing and therefore the secondary output voltage will increase, too. If the IC is operating with small pulse width of the output pulse the control amplifier applies an additional current to the control amplifier in order to reduce the output voltage. The value of the additional current depends on the size of the resistors R 5 , R 8 , R 7 . This can be used to compensate the increase of the secondary voltages. Behaviour if the Chip Temperature Exceeds Predefined Limits An integrated protection circuit against over temperature disables the internal logic if the chip temperature is too high. The internal logic automatically checks the chip temperature and restart the SMPS as soon as the temperature decreases to a permissible level. |
类似零件编号 - TDA4605-2 |
|
类似说明 - TDA4605-2 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |