数据搜索系统,热门电子元器件搜索 |
|
LB1863M 数据表(PDF) 4 Page - Sanyo Semicon Device |
|
LB1863M 数据表(HTML) 4 Page - Sanyo Semicon Device |
4 / 6 page Sample Application Circuit Output Waveforms No. 4943-4/6 LB1863M, 1869M Truth Table Design Documentation (See the application circuit diagram.) 1. Power-supply voltage (VIN pin) Since these miniature flat package products supply power to the Hall amplifier block and the control block from an internal parallel regulator, they operate with good stability with respect to kickback currents from the motor and variations in the power-supply voltage. They also provide an adequate ability to withstand surges. The resistor R1 between the VCC and VIN pins should be set up so that a current in the range ICC = 6 to 50 mA flows into the VIN pin in the fan motor power-supply voltage range. VIN has a typical value of 6.7 volts when ICC is 7 mA. The current flowing into VIN can be calculated with the following formula. VCC – VIN ICC = ————— ......................(1) R1 • Abnormal voltage considerations The maximum allowable current for the VIN pin is 200 mA. Therefore, the IC design allows it to withstand voltages up to the plus side abnormal voltage Vsurge give by formula (2). Vsurge = VIN + R1 × 200 mA......(2) 2. Hall input pin voltages (IN– and IN+ pins) The Hall element output voltages to the Hall element input pins must be in the range 0 to (VIN –1.5 V). The gain from the Hall input pins to the output pin is over 100 dB. The Hall input amplifier offset voltage is ±7 mV. This means that the Hall element output must be set up taking this ±7 mV offset into account. 3. Output transistors (OUT1 and OUT2 pins) Output current: IO = 1.5 A maximum Output saturation voltage: VOsat = 1.15V/1.0 A (typical) Applications should adopt one of the following three output protection techniques. ➀ If a capacitor is inserted between OUT and ground, use a capacitor with a value up to C = 10 μF, and design that value so that the kickback and reverse voltages do not exceed VOR. ➁ If a Zener diode is added, determine a value for the Zener voltage that is lower than VO(SUS). If radio-frequency noise is a problem, insert a capacitor between B1 and B2. ➂ If a capacitor is inserted between OUT and B1, set the capacitor value so that the kickback voltage is lower than VO(SUS). If oscillation occurs, insert a resistor in series with the capacitor. IN+ IN– C OUT1 OUT2 RD HL LHL L LHL LHL HLH H H H L H HHHH |
类似零件编号 - LB1863M |
|
类似说明 - LB1863M |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |