数据搜索系统,热门电子元器件搜索 |
|
LA4906 数据表(PDF) 6 Page - Sanyo Semicon Device |
|
LA4906 数据表(HTML) 6 Page - Sanyo Semicon Device |
6 / 10 page See the “Standby Function” section elsewhere in this document. TR1 · External switching transistor. The 2SD1668 (rank S) is recommended. If the application supports a load resistance RL of 4 Ω, a 2SD1667 (rank S) may be used. A heat sink must be provided for this transistor, as well as for the IC itself. D1 · Flywheel diode used to absorb energy from the coil. The SB40-05J, which is a Schottky barrier diode with a low VF, is recommended. If the application supports a load resistance RL of 4 Ω, an SB10-05A2 may be used. A heat sink must be provided for this diode, as well as for the IC itself. L1 · The Tokin Co., Ltd.-made HP-022Z [180 µH] (or the HP-011Z [200 µH] for 4- Ω applications) is recommended. 2. IC internal characteristics and other notes Switching regulator · The LA4906 includes a signal-following self-excited switching regulator to reduce power dissipation. The self- excitation frequency with no input signal is about 100 kHz. · To avoid spurious signal interference within the end product case, it is desirable to separate the tuner block from the amplifier block by as far as possible. When designing the printed circuit board pattern, make the lines associated with the switching regulator external components as short and as wide as possible. · To prevent degradation of the LA4906 characteristics, separate the switching regulator external components from the IC inputs (the input block pattern, the input capacitors, and the beep amplifier capacitor) by at least 1.5 cm. No. 5714-6/10 LA4906 Standby function · Pin 21 is the standby switching pin. The amplifier is turned on by applying a voltage of over 3 V to pin 21 through an external resistor (R1). · If the standby switch applied voltage will exceed 13.2 V, then the current flowing into pin 5 must be held to under 500 µ A. Use the following formula to determine the value of R1 that meets this condition. R1 = applied voltage – 1.4 V – 10 k Ω 500 µA BEEP pin (pin 4) · If the BEEP pin is used, use the smallest value of R102 (see figure) possible (but note that this value must be under 100 Ω) to prevent degradation of the IC's output noise voltage (VNO) characteristics. Protection circuits · The LA4906 includes an on-chip thermal protection circuit to prevent destruction of or damage to the IC if abnormal heating occurs. If, due to an inadequate heat sink or other reason, the IC junction temperature (Tj) reaches or exceeds 160°C, the output is gradually attenuated by the operation of the thermal protection circuit. · The overvoltage protection circuit operates if the VCC voltage exceeds 20 V. · While the LA4906 includes a power supply/ground short protection circuit, it does not include a load shorting protection circuit. The idea behind this design is that the thermal shutdown protection circuit will protect the IC itself if the load is shorted. However, since a load short will also cause temperature increases in the external transistor and coil, care is required in handling this case. Other notes · Pin 22 is not connected electrically to any other points within the package. Pin 21 IC Internal Equivalent Circuit Applied standby voltage 500 µA or less Beep signal About 1.4 V (2VBE) |
类似零件编号 - LA4906 |
|
类似说明 - LA4906 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |