数据搜索系统,热门电子元器件搜索 |
|
ISL22316WFU10Z 数据表(PDF) 4 Page - Intersil Corporation |
|
ISL22316WFU10Z 数据表(HTML) 4 Page - Intersil Corporation |
4 / 15 page 4 FN6186.2 September 1, 2009 RESISTOR MODE (Measurements between RW and RL with RH not connected, or between RW and RH with RL not connected) RINL (Note 15) Integral Non-linearity DCP register set between 10 hex and 7F hex; monotonic over all tap positions; W and U option -1 1 MI (Note 12) RDNL (Note 14) Differential Non-linearity W option -1 1 MI (Note 12) U option -0.5 0.5 MI (Note 12) Roffset (Note 13) Offset W option 0 1 5 MI (Note 12) U option 0 0.5 2 MI (Note 12) Analog Specifications Over recommended operating conditions, unless otherwise stated. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 19) TYP (Note 5) MAX (Note 19) UNIT Operating Specifications Over the recommended operating conditions, unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS MIN (Note 19) TYP (Note 5) MAX (Note 19) UNIT ICC1 VCC Supply Current (Volatile Write/Read) fSCL = 400kHz; SDA = Open; (for I 2C, active, read and write states) 0.5 mA ICC2 VCC Supply Current (Non-volatile Write/Read) fSCL = 400kHz; SDA = Open; (for I 2C, active, read and write states) 3mA ISB VCC Current (Standby) VCC = +5.5V @ +85°C, I 2C interface in standby state 5µA VCC = +5.5V @ +125°C, I 2C interface in standby state 7µA VCC = +3.6V @ +85°C, I 2C interface in standby state 3µA VCC = +3.6V @ +125°C, I 2C interface in standby state 5µA ISD VCC Current (Shutdown) VCC = +5.5V @ +85°C, I 2C interface in standby state 3µA VCC = +5.5V @ +125°C, I 2C interface in standby state 5µA VCC = +3.6V @ +85°C, I 2C interface in standby state 2µA VCC = +3.6V @ +125°C, I 2C interface in standby state 4µA ILkgDig Leakage Current, at Pins A0, A1, SHDN, SDA and SCL Voltage at pin from GND to VCC, SDA is inactive -1 1 µA tDCP (Note 18) DCP Wiper Response Time SCL falling edge of last bit of DCP data byte to wiper new position 1.5 µs tShdnRec (Note 18) DCP Recall Time from Shutdown Mode From rising edge of SHDN signal to wiper stored position and RH connection 1.5 µs SCL falling edge of last bit of ACR data byte to wiper stored position and RH connection 1.5 µs Vpor Power-on Recall Voltage Minimum VCC at which memory recall occurs 2.0 2.6 V VCCRamp VCC Ramp Rate 0.2 V/ms tD Power-up Delay VCC above Vpor, to DCP Initial Value Register recall completed and I2C Interface in standby state 3ms ISL22316 |
类似零件编号 - ISL22316WFU10Z |
|
类似说明 - ISL22316WFU10Z |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |