数据搜索系统,热门电子元器件搜索 |
|
CAT150029SWI-GT3 数据表(PDF) 5 Page - ON Semiconductor |
|
CAT150029SWI-GT3 数据表(HTML) 5 Page - ON Semiconductor |
5 / 15 page CAT15002, CAT15004 © 2008 SCILLC. All rights reserved. 5 Doc. No. MD-1126 Rev. B Characteristics subject to change without notice PIN DESCRIPTION RESET/RESET ¯¯¯¯¯¯: Reset output is available in two versions: CMOS Active Low (CAT150xx9) and CMOS Active High (CAT150xx1). Both versions are push-pull outputs for high efficiency. SI: The serial data input pin accepts op-codes, addresses and data. In SPI modes (0,0) and (1,1) input data is latched on the rising edge of the SCK clock input. SO: The serial data output pin is used to transfer data out of the device. In SPI modes (0,0) and (1,1) data is shifted out on the falling edge of the SCK clock. SCK: The serial clock input pin accepts the clock provided by the host and used for synchronizing communication between host and CAT15002/04. CS ¯¯ : The chip select input pin is used to enable/disable the CAT15002/04. When CS ¯¯ is high, the SO output is tri-stated (high impedance) and the device is in Standby Mode (unless an internal write operation is in progress). Every communication session between host and CAT15002/04 must be preceded by a high to low transition and concluded with a low to high transition of the CS ¯¯ input. WP ¯¯¯: The write protect input pin will allow all write operations to the device when held high. When WP ¯¯¯ pin is tied low all write operations are inhibited. DEVICE OPERATION The CAT15002/04 products combine the accurate voltage monitoring capabilities of a standalone voltage supervisor with the high quality and reliability of standard EEPROMs from Catalyst Semiconductor. RESET CONTROLLER DESCRIPTION The reset signal is asserted LOW for the CAT150xx9 and HIGH for the CAT150xx1 when the power supply voltage falls below the threshold trip voltage and remains asserted for at least 140ms (tPURST) after the power supply voltage has risen above the threshold. Reset output timing is shown in Figure 1. The CAT15002/04 devices protect µPs against brown-out failure. Short duration VCC transients of 4µsec or less and 100mV amplitude typically do not generate a Reset pulse. VCC PURST t PURST t RPD t RVALID V V TH RESE T RESE T CAT150xx9 CAT150xx1 RPD t Figure 1. RESET Output Timing |
类似零件编号 - CAT150029SWI-GT3 |
|
类似说明 - CAT150029SWI-GT3 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |