数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

SI-8001FDE 数据表(PDF) 6 Page - Sanken electric

部件名 SI-8001FDE
功能描述  DC-to-DC Step-Down Converter
Download  9 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  SANKEN [Sanken electric]
网页  http://www.sanken-ele.co.jp/en
标志 SANKEN - Sanken electric

SI-8001FDE 数据表(HTML) 6 Page - Sanken electric

  SI-8001FDE Datasheet HTML 1Page - Sanken electric SI-8001FDE Datasheet HTML 2Page - Sanken electric SI-8001FDE Datasheet HTML 3Page - Sanken electric SI-8001FDE Datasheet HTML 4Page - Sanken electric SI-8001FDE Datasheet HTML 5Page - Sanken electric SI-8001FDE Datasheet HTML 6Page - Sanken electric SI-8001FDE Datasheet HTML 7Page - Sanken electric SI-8001FDE Datasheet HTML 8Page - Sanken electric SI-8001FDE Datasheet HTML 9Page - Sanken electric  
Zoom Inzoom in Zoom Outzoom out
 6 / 9 page
background image
6
SANKEN ELECTRIC CO., LTD.
DC-to-DC Step-Down Converter
SI-8001FDE
27469.056
Component Selection
VIN
1
GND
GND
2
4
3
GND
SS
IN
SW
ADJ
C1
C2
L1
Di
VO
R1
R2
IADJ
5
C3
Soft Start Only
SI-8001FDE
Component
Rating
C1
470 μF
C2
680 μF
C3
0.1 μF (For soft start function)
Di
SPB-G56S (Sanken)
L1
47 μH
All external components should be mounted as close as possible
to the SI-8001FDE. The ground of all components should be
connected at one point near GND pin (pin 3).
Recommended PCB Layout
Recommended Solder Pad Layout
Typical Application Diagram
Diode Di
A Schottky-barrier diode must be used for Di. If other
diode types are used, such as fast recovery diodes, the IC may be
destroyed because of the reverse voltage applied by the recovery
voltage or ON voltage.
Choke Coil L1
If the winding resistance of the choke coil is too
high, the efficiency may be reduced below rating. Because the
overcurrent protection start current is approximately 4.2 A, atten-
tion must be paid to the heating of the choke coil by magnetic
saturation due to overload or short-circuited load.
Capacitors C1, C2, and C3
Because for SMPS, large ripple
currents flow across C1 and C2, capacitors with high frequency
and low impedance must be used. If the impedance of C2 is too
high, the switching waveform may not be normal at low tempera-
tures. Do not use either OS or tantalum types of capacitors for
C2 or C3, because the extremely low ESR causes an abnormal
oscillation.
The device is stabilized, and for proper operation, C1 must be
located close to the device (see layout diagram, below). C3 is
required only if the soft start function is used. If not using soft-
start, leave the SS terminal open. A pull-up resistor is provided
inside the IC.
Resistor Bridge
R1 and R2 comprise the resistor bridge for the
output voltage, VO, and are calculated as follows:
() () ) , and
(
()
Ω
×
==
=
Ω
×
=
=
k
I
V
R2
V
I
V
V
R1
ADJ
ADJ
O
ADJ
ADJ
O
8
.
0
10
1
8
.
0
10
1
8
.
0
3
3
IADJ should always be set to 1 mA. Note that R2 should always be
present to ensure stable operation, even if VO, is set to 0.8 V (that
is, even if there is no R1). VO should be at least VIN + 8%.
6.8±0.1
11±0.2
9±0.2
9±0.1
3.7±0.05
4±0.1
1.7±0.1
1±0.05
(mm)


类似零件编号 - SI-8001FDE

制造商部件名数据表功能描述
logo
Sanken electric
SI-8001FDE SANKEN-SI-8001FDE Datasheet
68Kb / 2P
   Surface Mount, Separate Excitation Step-down Switching Mode
SI-8001FDE SANKEN-SI-8001FDE Datasheet
296Kb / 9P
   DC-to-DC Step-Down Converter
More results

类似说明 - SI-8001FDE

制造商部件名数据表功能描述
logo
Sanken electric
SI-8008HD SANKEN-SI-8008HD Datasheet
423Kb / 2P
   DC-to-DC Step-Down Converter
SI-8008HFE SANKEN-SI-8008HFE Datasheet
307Kb / 2P
   DC-to-DC Step-Down Converter
SI-8001FDE SANKEN-SI-8001FDE Datasheet
296Kb / 9P
   DC-to-DC Step-Down Converter
logo
Holtek Semiconductor In...
HT7465 HOLTEK-HT7465_14 Datasheet
1Mb / 9P
   Step-Down DC to DC Converter
logo
Sanken electric
SI-8001FFE SANKEN-SI-8001FFE Datasheet
242Kb / 9P
   DC-to-DC Step-Down Converter
SI-8001FFE SANKEN-SI-8001FFE Datasheet
316Kb / 9P
   DC-to-DC Step-Down Converter
SI-8001FDL SANKEN-SI-8001FDL Datasheet
331Kb / 2P
   DC-to-DC Step-Down Converter
logo
Holtek Semiconductor In...
HT7466 HOLTEK-HT7466_14 Datasheet
1Mb / 9P
   3A Step-Down DC to DC Converter
HT7465 HOLTEK-HT7465 Datasheet
1Mb / 11P
   2A Step-Down DC to DC Converter
HT7466 HOLTEK-HT7466 Datasheet
1Mb / 9P
   3A Step-Down DC to DC Converter
More results


Html Pages

1 2 3 4 5 6 7 8 9


数据表 下载

Go To PDF Page


链接网址




隐私政策
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com