数据搜索系统,热门电子元器件搜索 |
|
STK433-130-E 数据表(PDF) 8 Page - Sanyo Semicon Device |
|
STK433-130-E 数据表(HTML) 8 Page - Sanyo Semicon Device |
8 / 11 page STK433-130-E No. A1596-8/11 [Example] When the IC supply voltage, VCC, is ±44V and RL is 6Ω, the total power dissipation, Pd, within the hybrid IC, will be a maximum of 130W at 1kHz for a continuous sine wave signal according to the Pd-PO characteristics. For the music signals normally handled by audio amplifiers, a value of 1/8PO max is generally used for Pd as an estimate of the power dissipation based on the type of continuous signal. (Note that the factor used may differ depending on the safety standard used.) This is: Pd ≈ 87W (when 1/8PO max. = 12.5W, PO max. = 150W). The number of power transistors in audio amplifier block of these hybrid ICs, N, is 4, and the thermal resistance per transistor, θj-c, is 1.6°C/W. Therefore, the required heat sink thermal resistance for a guaranteed ambient temperature, Ta, of 50 °C will be as follows. From formula (1)' θc-a < (125 − 50)/87 < 0.86 From formula (2)' θc-a < (150 − 50)/87 − 1.6/4 < 0.74 Therefore, the value of 0.74 °C/W, which satisfies both of these formulae, is the required thermal resistance of the heat sink. Note that this thermal design example assumes the use of a constant-voltage power supply, and is therefore not a verified design for any particular user’s end product. STK433-100 Series Standby Control, Mute Control, Load-short Protection & DC offset Protection application 2 3 4 5 6 7 8 9 10 11 12 13 14 1 15 Ch1 OUT GND +VCC -VCC STK433-100 series ST-BY 56k Ω GND Ch2 IN GND Ch1 IN +VCC Ch1 IN Ch1 NF Ch2 IN Ch2 NF Ch2 OUT Ch1 OUT -VCC SUB GND +PRE ST-BY Ch1 OUT Ch2 OUT -PRE 6.8k Ω 56k Ω 6.8k Ω Load short protection circuit 22k Ω 56k Ω 1k Ω 0.1 μF 10k Ω 100kΩ (*4) R2 1k Ω 33k Ω 2k Ω (*1) 13k Ω 33 μF /10V 10k Ω 10k Ω 10k Ω 2.2k Ω GND Ch2 OUT 82k Ω 82k Ω 100 k Ω 22 μF 22 μF PLAY MUTE ST-BY MUTE +5V +5V Standby Control Mute Control Mute Control H: Single Mute L: Normal Stand-by Control (ex) H: Operation Mode (+5V) L: Stand-by Mode (0V) DC offset protection (*1) The current flowing into the Stand-by pin (#13) must not exceed the maximum rated value (IST max). Latch up circuit |
类似零件编号 - STK433-130-E |
|
类似说明 - STK433-130-E |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |