数据搜索系统,热门电子元器件搜索 |
|
AD1072F 数据表(PDF) 2 Page - MicroPower Direct, LLC |
|
AD1072F 数据表(HTML) 2 Page - MicroPower Direct, LLC |
2 / 2 page Derating Curve Model Selection Guide Mechanical Dimensions Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com Model Number Rated Power (W) Input Output Overvoltage Protection (VDC) Ripple & Noise (mV p-p) Efficiency (%, Typ) Voltage (VAC) Current (A) Voltage (VDC) Current (A) Max) Current (A) Range Universal Range 115 VAC 230 VAC AD1072-12F 72 100 - 240 1.0 0.5 12 6.0 0 ~ 6.0 15 ~ 17 100 78 AD1072-24F 72 100 - 240 1.0 0.5 24 3.0 0 ~ 3.0 27 ~ 30 150 81 AD1072-48F 72 100 - 240 1.0 0.5 48 1.5 0 ~ 1.5 52 ~ 56 250 82 Notes: 1. Load regulation is specified for a load change of 20% to 100%. 2. Ripple & noise is measured using equipment with 20 Mhz of bandwidth with the unit under test operating at rated load and a 110 VAC input. Connection to the unit is made with a 0.1 μF / 630V metalized capacitor & a 47 μF electrolytic capacitor connected in parallel. 3. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 4. Isolation resistance is given for Input/Output and Input/FG. For Output/FG., it is 50 M Ω 5. Overload protection is power limiting. The unit recovers automatically when the fault is removed. 6. Over voltage protection is a shut down type. The unit recovers automatically when the fault is removed. 7. To mount the unit to the DIN rail, tilt the unit rearwards from the top, fitting the mount over the top of the rail. Press back on the bottom front of the unit until it locks in place on the rail. To remove the unit from the rail, pull the removal clip at the bottom rear of the unit downward with a screw driver. With the clip down, lift up on the unit from the bottom front until it clears the rail. Before installation or removal all wiring should be disconnected and the main power to the system shut off. 8. When wiring the supply, all lines should be as thick and short as possible. AWG 14 wire is recommended for the AD1072F series. 9. The units should be mounted so they are vertically orientated. Air flow (if it is provided) would optimally flow from the bottom to the top of the unit. 10. It is recommended that a fuse be used on the input of a power supply for protection. For the AD1072F series a 250VAC 2.0A is recom- mended. Connections TB 1 Pin Function 1 DC Output (+V) 2 DC Output (-V) 3 FT (Optional) 4 FT (Optional) 5 Frame Ground (FG) 6 AC Input - Neutral 7 AC Input - Live Units with the optional “FT” outputs may be easily connected for “Fault Tolerant operation. Contact the factory for details |
类似零件编号 - AD1072F |
|
类似说明 - AD1072F |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |