数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

TS68HC901CP5 数据表(PDF) 5 Page - STMicroelectronics

部件名 TS68HC901CP5
功能描述  HCMOS MULTI-FUNCTION PERIPHERAL
Download  42 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

TS68HC901CP5 数据表(HTML) 5 Page - STMicroelectronics

  TS68HC901CP5 Datasheet HTML 1Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 2Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 3Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 4Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 5Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 6Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 7Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 8Page - STMicroelectronics TS68HC901CP5 Datasheet HTML 9Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 42 page
background image
RS1-RS5:
(A1-A5)
Register Address Bus (inputs). The ad-
dress bus is used to address one of the
internal registers during a read or write
cycle.
D0-D7 :
Data Bus (bi-directional, tri-stateable).
This bus is used to receive data from or
transmit data to the MFP’s internal regis-
ters during a processor read or write cy-
cle. During an interrupt acknowledge cy-
cle, the data bus is used to pass a vector
number to the processor. Since the MFP
is an 8-bit peripheral, the MFP could be
located on either the upper or lower por-
tion of the 16-bit data bus (even or odd
address). However, during an interrupt
acknowledge cycle, the vector number
passed to the processor must be located
in the low byte of the data word. As a re-
sult, D0-D7 of the MFP must be connec-
ted to the low eight bits of the processor
data bus, placing MFP registers at odd
addresses if vectored interrupt are to be
used.
CLK :
The clock input is a single-phase TTL
compatible signal used for internal ti-
ming . This input should not be gated off
at any time and must conform to mini-
mum and maximum pulse width times.
The clock is not necessarily the system
clock in frequency nor phase. When the
bus is multiplexed (MPX=1), an address
strobe signal is connected to this pin. In
the non multiplexed mode (MPX=0), this
input is connected to the system clock
when used with a 68000 processor type
or to VSS (0VDC) when used with a 6800
processor type.
RESET : Device reset. (input, active low). Reset
disables the USART receiver and trans-
mitter, stops all timers and forces the ti-
mer outputs low, disables all interrupt
channels and clears any pending inter-
rupts. The General Purpose Interrupt/I/O
lines will be placed in the tri-state input
mode. All internal registers (except the ti-
mer, USART data registers, and transmit
status register) will be cleared.
MPX :
This input selects the data bus mode:
MPX = 0 : non multiplexed mode
MPX = 1 : multiplexed mode. The register
select lines RS1-RS5 and the data bus
D0-D7 are multiplexed. An address
strobe must be connected to the CLK pin.
IRQ :
Interrupt Request (output, active low, o-
pen drain). This output signals the pro-
cessor that an interrupt is pending from
the CMFP. These are 16 interrupt chan-
nels that can generate an interrupt re-
quest. Clearing the interrupt pending re-
gisters (IPRA and IPRB) or clearing the
interrupt mask registers (IMRA and
IMRB) will cause IRQ to be negated. IRQ
will also be negated as the result of an in-
terrupt acknowledge cycle, unless addi-
tional i nterrupts are pending in the
CM FP. Ref er to par agraph INTER-
RUPTS for further information.
IACK :
Interrupt Acknowledge (input, active
l ow ). IACK i s us ed t o s ignal t he
TS68HC901 that the CPU is acknow-
ledging an interrupt. CS and IACk must
not be asserted at the same time.
IEI :
Interrupt Enable In (input, active low). IEI
is used to signal the TS68HC901 that no
higher priority device is requesting inter-
rupt service.
IEO :
Interrupt Enable Out (output, active low).
IEO is used to signal lower priority peri-
pherals that neither the TS68HC901 nor
another higher priority peripheral is re-
questing interrupt service.
I0-I7 :
Ge neral Purpose Interrupt I/O lines.
These lines may be used as interrupt in-
puts and/or I/O lines. When used as inter-
rupt inputs, their active edge is program-
mable. A data direction register is used to
define which lines are to be Hi-Z inputs
and which lines are to be push-pull TTL
compatible outputs.
SO :
Serial Output. This is the output of the U-
SART transmitter.
SI :
Serial Input. This is the input to the U-
SART receiver.
RC :
Receiver Clock. This input controls the
serial bit rate of the USART receiver.
TC :
Transmitter Clock. This input controls the
serial bit rate of the USART transmitter.
RR :
Receiver Ready. (output, active low)
DMA output for receiver, which reflects
the status of Buffer Full in port number
15.
TR :
Transmitter Ready. (output, active low)
DMA output for transmitter, which re-
flects the status of Buffer Empty in port
number 16.
®
TS68HC901
5/42


类似零件编号 - TS68HC901CP5

制造商部件名数据表功能描述
logo
STMicroelectronics
TS68000 STMICROELECTRONICS-TS68000 Datasheet
4Mb / 76P
   HMOS 16/32-BIT MICROPROCESSOR
TS68000CFN10 STMICROELECTRONICS-TS68000CFN10 Datasheet
4Mb / 76P
   HMOS 16/32-BIT MICROPROCESSOR
TS68000CFN16 STMICROELECTRONICS-TS68000CFN16 Datasheet
4Mb / 76P
   HMOS 16/32-BIT MICROPROCESSOR
TS68000CFN8 STMICROELECTRONICS-TS68000CFN8 Datasheet
4Mb / 76P
   HMOS 16/32-BIT MICROPROCESSOR
TS68000CP10 STMICROELECTRONICS-TS68000CP10 Datasheet
4Mb / 76P
   HMOS 16/32-BIT MICROPROCESSOR
More results

类似说明 - TS68HC901CP5

制造商部件名数据表功能描述
logo
Motorola, Inc
MC68HC901 MOTOROLA-MC68HC901 Datasheet
274Kb / 43P
   Multi-Function Peripheral
logo
List of Unclassifed Man...
BL1R ETC2-BL1R Datasheet
611Kb / 3P
   Multi-function or mono-function
BM1R ETC2-BM1R Datasheet
772Kb / 4P
   Multi-function or mono-function
BM2R ETC2-BM2R Datasheet
774Kb / 4P
   Multi-function or mono-function
BA1R ETC2-BA1R Datasheet
570Kb / 4P
   Multi-function or mono-function
logo
SMSC Corporation
USB97C100 SMSC-USB97C100 Datasheet
434Kb / 64P
   Multi-Endpoint USB Peripheral Controller
logo
Microsemi Corporation
TSC341 MICROSEMI-TSC341 Datasheet
726Kb / 4P
   Multi-Function Gates
logo
Qualtek Electronics Cor...
761-18-003 QUALTEK-761-18-003 Datasheet
379Kb / 1P
   MULTI-FUNCTION MODULE
755-00-28 QUALTEK-755-00-28 Datasheet
367Kb / 1P
   MULTI-FUNCTION MODULE
762-18-003 QUALTEK-762-18-003 Datasheet
376Kb / 1P
   MULTI-FUNCTION MODULE
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42


数据表 下载

Go To PDF Page


链接网址




隐私政策
ALLDATASHEETCN.COM
ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com