数据搜索系统,热门电子元器件搜索 |
|
L6917 数据表(PDF) 7 Page - STMicroelectronics |
|
L6917 数据表(HTML) 7 Page - STMicroelectronics |
7 / 33 page 7/33 L6917B 16 ISEN2 Channel 2 current sense pin. The output current may be sensed across a sense resistor or across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain or to the sense resistor through a resistor Rg in order to program the positive current limit at 140% as follow: Where 35 µA is the current offset information relative to the Over Current condition (offset at OC threshold minus offset at zero load). The net connecting the pin to the sense point must be routed as close as possible to the PGNDS2 net in order to couple in common mode any picked-up noise. 17 OSC/ INH/ FAULT Oscillator switching frequency pin. Connecting an external resistor from this pin to GND, the external frequency is increased according to the equation: Connecting a resistor from this pin to Vcc (12V), the switching frequency is reduced according to the equation: If the pin is not connected, the switching frequency is 300KHz. Forcing the pin to a voltage lower than 0.8V, the device stop operation and enter the inhibit state. The pin is forced high when an over or under voltage is detected. This condition is latched; to recover it is necessary turn off and on VCC. 18-22 VID4-0 Voltage IDentification pins. These input are internally pulled-up and TTL compatible. They are used to program the output voltage as specified in Table 1 and to set the power good thresholds. Connect to GND to program a ‘0’ while leave floating to program a ‘1’. 23 PGOOD This pin is an open collector output and is pulled low if the output voltage is not within the above specified thresholds. If not used may be left floating. 24 BOOT2 Channel 2 bootstrap capacitor pin. Through this pin is supplied the high side driver and the upper mosfet. Connect through a capacitor to the PHASE2 pin and through a diode to Vcc (cathode vs. boot). 25 UGATE2 Channel 2 high side gate driver output. 26 PHASE2 This pin is connected to the source of the upper mosfet and provides the return path for the high side driver of channel 2. 27 LGATE2 Channel 2 low side gate driver output. 28 PGND Power ground pin. This pin is common to both sections and it must be connected through the closest path to the low side mosfets source pins in order to reduce the noise injection into the device. PIN FUNCTION (continued) N Name Description I MA X 35 µAR g ⋅ R se nse -------------------------- = f S 300KHz 14.82 10 6 ⋅ R OSC K Ω () ----------------------------- + = f S 300KHz 12.91 10 7 ⋅ R OSC K Ω () ----------------------------- – = |
类似零件编号 - L6917 |
|
类似说明 - L6917 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |