数据搜索系统,热门电子元器件搜索 |
|
L6918 数据表(PDF) 5 Page - STMicroelectronics |
|
L6918 数据表(HTML) 5 Page - STMicroelectronics |
5 / 35 page 5/35 L6918 L6918A L6918 (SLAVE) PIN FUNCTION N. Name Description 1 LGATE1 Channel 1 low side gate driver output. 2 VCCDR LS Mosfet driver supply. 5V or 12V buses can be used. 3 PHASE1 This pin is connected to the Source of the upper mosfet and provides the return path for the high side driver of channel 1. 4 UGATE1 Channel 1 high side gate driver output. 5 BOOT1 Channel 1 bootstrap capacitor pin. This pin supplies the high side driver. Connect through a capacitor to the PHASE1 pin and through a diode to Vcc (cathode vs. boot). 6 VCC Device supply voltage. The operative supply voltage is 12V. 7 GND All the internal references are referred to this pin. Connect it to the PCB signal ground. 8 COMP This pin is connected to the error amplifier output and is used to compensate the control feedback loop. 9 FB This pin is connected to the error amplifier inverting input and is used to compensate the voltage control feedback loop. A current proportional to the sum of the current sensed in both channel is sourced from this pin (50 µA at full load, 70µA at the Over Current threshold). Connecting a resistor RFB between this pin and VSEN pin allows programming the droop effect. 10 VSEN Connected to the output voltage it is able to manage Over & Under-voltage conditions and the PGOOD signal. It is internally connected with the output of the Remote Sense Buffer for Remote Sense of the regulated voltage. If no Remote Sense is implemented, connect it directly to the regulated voltage in order to manage OVP, UVP and PGOOD. 11 FBR Remote sense buffer non-inverting input. It has to be connected to the positive side of the load to perform a remote sense. If no remote sense is implemented, connect directly to the output voltage (in this case connect also the VSEN pin directly to the output regulated voltage). 12 FBG Remote sense buffer inverting input. It has to be connected to the negative side of the load to perform a remote sense. Pull-down to ground if no remote sense is implemented. 13 ISEN1 Channel 1 current sense pin. The output current may be sensed across a sense resistor or across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain or to the sense resistor through a resistor Rg in order to program the current intervention for each phase at 140% as follow: Where 35 µA is the current offset information relative to the Over Current condition (offset at OC threshold minus offset at zero load). The net connecting the pin to the sense point must be routed as close as possible to the PGNDS1 net in order to couple in common mode any picked-up noise. 14 PGNDS1 Channel 1 Power Ground sense pin. The net connecting the pin to the sense point must be routed as close as possible to the ISEN1 net in order to couple in common mode any picked-up noise. 15 PGNDS2 Channel 2 Power Ground sense pin. The net connecting the pin to the sense point must be routed as close as possible to the ISEN2 net in order to couple in common mode any picked-up noise. I OC Px 35 µAR g ⋅ R s ens e -------------------------- = |
类似零件编号 - L6918 |
|
类似说明 - L6918 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |