SL811HS
Document 38-08008 Rev. *D
Page 3 of 32
PLL Clock Generator
Either a 12 MHz or a 48 MHz external crystal is used with the
SL811HS[1]. Two pins, X1 and X2, are provided to connect a
low cost crystal circuit to the device as shown in Figure 2 and
Figure 3. Use an external clock source if available in the appli-
cation instead of the crystal circuit by connecting the source
directly to the X1 input pin. When a clock is used, the X2 pin
is not connected.
When the CM pin is tied to a logic 0, the internal PLL is
bypassed so the clock source must meet the timing require-
ments specified by the USB specification.
Typical Crystal Requirements
The following are examples of ‘typical requirements.’ Note that
these specifications are generally found as standard crystal
values and are less expensive than custom values. If crystals
are used in series circuits, load capacitance is not applicable.
Load capacitance of parallel circuits is a requirement. 48 MHz
third overtone crystals require the Cin/Lin filter to guarantee 48
MHz operation.
USB Transceiver
The SL811HS has a built in transceiver that meets USB Speci-
fication 1.1. The transceiver is capable of transmitting and
receiving serial data at USB full speed (12 Mbits) and low
speed (1.5 Mbits). The driver portion of the transceiver is differ-
ential while the receiver section is comprised of a differential
receiver and two single-ended receivers. Internally, the trans-
ceiver interfaces to the Serial Interface Engine (SIE) logic.
Externally, the transceiver connects to the physical layer of the
USB.
SL811HS Registers
Operation and control of the SL811HS is managed through
internal registers. When operating in Master/Host mode, the
first 16 address locations are defined as register space. In
Slave/Peripheral mode, the first 64 bytes are defined as
register space. The register definitions vary greatly between
each mode of operation and are defined separately in this
document (section “SL811HS Master (Host) Mode Registers”
on page 4 describes Host register definitions, while section
Note
1. CM (Clock Multiply) pin of the SL811HS must be tied to GND when 48 MHz crystal circuit or 48 MHz clock source is used.
Cbk
0.01
μF
Rs
100
X1
48 MHz, series, 20-pF load
Cout
22 pF
Rf
1M
X2
Cin
22 pF
Lin
2.2
μH
X1
Figure 2. Full Speed 48 MHz Crystal Circuit
X1
12 MHz , series, 20-pF load
Rf
1M
Cin
22 pF
Cout
22 pF
Rs
100
X2
X1
Figure 3. Optional 12 MHz Crystal Circuit
12 MHz Crystals:
Frequency Tolerance:
±100 ppm or better
Operating Temperature Range:
0
°C to 70°C
Frequency:
12 MHz
Frequency Drift over Temperature:
± 50 ppm
ESR (Series Resistance):
60
Ω
Load Capacitance:
10 pF min.
Shunt Capacitance:
7 pF max.
Drive Level:
0.1–0.5 mW
Operating Mode:
fundamental
48 MHz Crystals:
Frequency Tolerance:
±100 ppm or better
Operating Temperature Range:
0
°C to 70°C
Frequency:
48 MHz
Frequency Drift over Temperature:
± 50 ppm
ESR (Series Resistance):
40
Ω
Load Capacitance:
10 pF min.
Shunt Capacitance:
7 pF max.
Drive Level:
0.1–0.5 mW
Operating Mode:
third overtone
[+] Feedback
[+] Feedback
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
