数据搜索系统,热门电子元器件搜索 |
|
TDA6101Q 数据表(PDF) 7 Page - NXP Semiconductors |
|
TDA6101Q 数据表(HTML) 7 Page - NXP Semiconductors |
7 / 16 page 1995 Feb 07 7 Philips Semiconductors Preliminary specification Video output amplifier TDA6101Q Notes 1. If the difference between VDDL and Vip is less than 7 V, overshoot cannot be specified. 2. SVRR: The ratio of the change in supply voltage to the change in input voltage when there is no change in output voltage. Ov cathode output voltage overshoot VocAC = 100 V (p-p); VocDC = 100 V square wave; f < 1 MHz; tr =tf =40ns; see Figs 4 and 5; note 1 − 9 − % SVRRH high supply voltage rejection ratio f < 50 kHz; note 2 − 85 − dB SVRRL low supply voltage rejection ratio f < 50 kHz; note 2 − 70 − dB SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Cathode output The cathode output is protected against peak currents (caused by positive voltage peaks during high-resistance flash) of 5 A maximum with a charge content of 100 µC. The cathode is also protected against peak currents (caused by positive voltage peaks during low-resistance flash) of 10 A maximum with a charge content of 100 nC. Flashover protection The TDA6101Q incorporates protection diodes against CRT flashover discharges that clamp the cathode output pin to the VDDH pin. The DC supply voltage at the VDDH pin has to be within the operating range of 180 to 210 V to ensure that the Absolute Maximum Rating for VDDH of 250 V will not be exceeded during flashover. To limit the diode current, an external 820 Ω carbon high-voltage resistor in series with the cathode output and a 2 kV spark gap are needed (for this resistor-value, the CRT has to be connected to the main PCB). This addition produces an increase in the rise and fall times of approximately 5 ns and a decrease in the overshoot of approximately 3%. VDDH to GND must be decoupled: 1. With a capacitor >20 nF with good HF behaviour (e.g. foil). This capacitance must be placed as close as possible to pins 6 and 4, but definitely within 5 mm. 2. With a capacitor >10 µF on the picture tube base print (common for three output stages). VDDL to GND must be decoupled: 1. With a capacitor >20 nF with good HF behaviour (e.g. ceramic). This capacitance must be placed as close as possible to pins 2 and 4, but definitely within 10 mm. Switch-off behaviour The switch-off behaviour of the TDA6101Q is defined: when the bias current becomes zero, at VDDL (pin 2) lower than approximately 5 V, all the output pins (pins 7, 8 and 9) will be high. |
类似零件编号 - TDA6101Q |
|
类似说明 - TDA6101Q |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |