数据搜索系统,热门电子元器件搜索 |
|
TDA4882 数据表(PDF) 11 Page - NXP Semiconductors |
|
TDA4882 数据表(HTML) 11 Page - NXP Semiconductors |
11 / 28 page 1997 Sep 04 11 Philips Semiconductors Product specification Advanced monitor video controller for OSD TDA4882 Notes to the characteristics 1. Definition of levels: a) Artificial black level: internal signal level behind input emitter follower during input clamping and signal clipping. This level is inserted instead of the input signal during blanking. b) Reference black level: DC voltage during output clamping at voltage outputs, not influenced by brightness, contrast or gain setting, adjustable by cut-off stabilization. c) Cut-off level: corresponding DC voltage at CRT cathode in closed feedback loop. d) Black level: actual signal black level at either the voltage outputs or cathode, it can be adjusted by (brightness × gain), it refers to reference black level or cut-off level. e) Ultra-black level, switch-off level: lowest adjustable reference black level, lowest signal level at voltage outputs. f) The minimum guaranteed control range for reference black level is 0.1 to 1 V. The ultra-black level is dependent on the external resistor RO at pins 13, 16 and 19 (voltage outputs) to ground. g) 2. Linear control range is 1 to 6 V for Vi(BC), independent of supply voltage. 3. Linear control range is 1 to 6 V for Vi(CC), independent of supply voltage. Open pin 6 leads to maximum contrast setting. It is recommended not to exceed Vi(CC) =VP − 1 V to avoid saturation of internal circuitry. For Vi(CC) <Vi(CC)(min) ≈ 0.7 V a small negative signal (≈−40 dB) will appear. For frequency dependency of contrast control see note 15. 4. Definition for nominal output signals: input Vi(b-w) = 0.7 V, gain pins 3 and 11 open-circuit, contrast control Vi(CC) =Vi(CC)(nom). 5. dB Ax: signal output amplitude in channel x at any contrast setting between 1 and 6 V. Ax0: signal output amplitude in channel x at nominal contrast and same gain setting. 6. Typical step in contrast voltage and response at signal outputs for nominal input signal Vi(b-w) = 0.7 V (OSD fast blanking input/output). 7. Linear control range is 1 to 6 V for Vi(GC), independent of supply voltage. 8. The internal reference voltage can be measured at pins 18, 15 and 12 (channel feedback inputs) during output clamping (Vi(HBL) = 2 V) in closed feedback loop. 9. Slow variations of video supply voltage VCRT (Fig.1) will be suppressed at CRT cathode by cut-off stabilization. Change of VCRT by 5 V leads to specified change of cut-off voltage. 10. The test mode allows testing without input and output clamping pulses. The signal inputs have to be biased via resistors to the previously measured clamp voltages of approximately 3 V (artificial black level + VBE). Signal and brightness blanking is not possible during test mode. The current outputs should be adjusted by resistors >> R0 from voltage outputs to a positive voltage (e.g. VP). tr(CL), tf(CL) rise and fall time for clamping pulse note 19; Fig.17 −− 75 ns/V tw(clamp) width of clamping pulse 0.6 −−µs td(Vblank) delay between vertical blanking input and internal blanking note 19; Fig.17 260 320 380 ns SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V bl(SO) R o 3.5 k Ω R o + ------------------------------- 4.65 V × ≈ ∆G track 20 maximum of A 1 A 10 --------- A 20 A 2 --------- × log A 1 A 10 --------- A 30 A 3 --------- × log A 2 A 20 --------- A 30 A 3 --------- × log ; ; × = |
类似零件编号 - TDA4882 |
|
类似说明 - TDA4882 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |