数据搜索系统,热门电子元器件搜索 |
|
TPIC74100QPWPRQ1 数据表(PDF) 10 Page - Texas Instruments |
|
|
TPIC74100QPWPRQ1 数据表(HTML) 10 Page - Texas Instruments |
10 / 30 page www.ti.com Modulator Frequency Setting (Terminal Rmod) Ground Terminal (PGND) Enable Terminal (ENABLE) Bootstrap Terminals (Cboot1 and Cboot2) Functional Modes Clock Modulator Buck/Boost Transitioning TPIC74100-Q1 BUCK/BOOST SWITCH-MODE REGULATOR SLIS125 – DECEMBER 2006 See the converter efficiency plots in the Typical Characteristics section to determine power dissipation. The Rmod terminal adjusts the clock modulator frequency. A resistor of Rmod = 12 kΩ generates a modulation frequency of 28 kHz. The modulator function may be disabled by connecting Rmod to GND and the device operates with the nominal frequency. The modulator function cannot be activated during IC operation, only at IC start-up. The PGND terminal is the power ground for the device. The ENABLE terminal allows the enabling and disabling of the switch mode regulator. A maximum of 40 V may be applied to this terminal to enable the device and increasing it above the V(driver) input voltage does not affect the device operation. The functionality of the ENABLE terminal is described in the following table: ENABLE Function 0 Vreg is off. Open Undefined 1 Vreg is on. An external bootstrap capacitor is required for driving the internal high-side MOSFET switch. A 4.7-nF ceramic capacitor is typically required. To minimize EMI issues associated with the switch-mode regulator, the device offers an integrated clock modulator. The function of the clock modulator is to modulate the switching frequency and to distribute the energy over the wave band. The average switching frequency is 440 kHz (typical) and varies between 330 kHz and 550 kHz at a rate set by the Rmod resistor. A typical value of 12 kΩ on the Rmod terminal relates to a 28-kHz modulation frequency. The clock modulator function can only be activated during IC start-up, not during IC operation. The equation for the modulation frequency is as follows: f(mod) (Hz) = (–2.2 × Rmod) + 54.5 kHz, when Rmod = 8 kΩ to 16 kΩ The operation mode switches automatically between buck and boost modes depending on the input voltage of V(driver) and output load conditions. During start up, when V(driver) is less than 5.8 V (typical), the device starts in boost mode and continues to run in boost mode until V(driver) exceeds 5.8 V; at which time, the device switches over to buck mode. In buck mode, the device continues to run in buck mode until it is required to switch back to boost to hold regulation. This crossover window to switch to boost mode is when V(driver) is between 5.8 V and 5 V and depends on the loading conditions. When Vdriver drops below 5.8 V but the device is holding regulation (~2%), the device remains in buck mode. However, when V(driver) is within the 5.8-V to 5-V window and VOUT drops to 4.9 V, the device crosses over to boost mode to hold regulation. In boost mode, the device remains in boost mode until V(driver) exceeds 5.8 V; at which time, the device enters the buck mode. When the device is 10 Submit Documentation Feedback |
类似零件编号 - TPIC74100QPWPRQ1 |
|
类似说明 - TPIC74100QPWPRQ1 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |