数据搜索系统,热门电子元器件搜索 |
|
LM2903VDR2G 数据表(PDF) 3 Page - ON Semiconductor |
|
LM2903VDR2G 数据表(HTML) 3 Page - ON Semiconductor |
3 / 10 page LM393, LM293, LM2903, LM2903V, NCV2903 http://onsemi.com 3 ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, Tlow ≤ TA ≤ Thigh, unless otherwise noted.) Characteristic Symbol LM293, LM393 LM2903, LM2903V, NCV2903 Unit Min Typ Max Min Typ Max Input Offset Voltage (Note 5) VIO mV TA = 25°C − ±1.0 ±5.0 − ±2.0 ±7.0 Tlow ≤ TA ≤ Thigh − − 9.0 − 9.0 15 Input Offset Current IIO nA TA = 25°C − ±5.0 ±50 − ±5.0 ±50 Tlow ≤ TA ≤ Thigh − − ±150 − ±50 ±200 Input Bias Current (Note 6) IIB nA TA = 25°C − 25 250 − 25 250 Tlow ≤ TA ≤ Thigh − − 400 − 200 500 Input Common Mode Voltage Range (Note 6) VICR V TA = 25°C 0 − VCC −1.5 0 − VCC −1.5 Tlow ≤ TA ≤ Thigh 0 − VCC −2.0 0 − VCC −2.0 Voltage Gain AVOL 50 200 − 25 200 − V/mV RL ≥ 15 kW, VCC = 15 Vdc, TA = 25°C Large Signal Response Time − − 300 − − 300 − ns Vin = TTL Logic Swing, Vref = 1.4 Vdc VRL = 5.0 Vdc, RL = 5.1 kW, TA = 25°C Response Time (Note 8) tTLH − 1.3 − − 1.5 − ms VRL = 5.0 Vdc, RL = 5.1 kW, TA = 25°C Input Differential Voltage (Note 9) VID − − VCC − − VCC V All Vin ≥ GND or V− Supply (if used) Output Sink Current ISink 6.0 16 − 6.0 16 − mA Vin ≥ 1.0 Vdc, Vin+ = 0 Vdc, VO ≤ 1.5 Vdc TA = 25°C Output Saturation Voltage VOL mV Vin ≥ 1.0 Vdc, Vin+ = 0, ISink ≤ 4.0 mA, TA = 25°C − 150 400 − − 400 Tlow ≤ TA ≤ Thigh − − 700 − 200 700 Output Leakage Current IOL nA Vin− = 0 V, Vin+ ≥ 1.0 Vdc, VO = 5.0 Vdc, TA = 25°C − 0.1 − − 0.1 − Vin− = 0 V, Vin+ ≥ 1.0 Vdc, VO = 30 Vdc, Tlow ≤ TA ≤ Thigh − − 1000 − − 1000 Supply Current ICC mA RL = ∞ Both Comparators, TA = 25°C − 0.4 1.0 − 0.4 1.0 RL = ∞ Both Comparators, VCC = 30 V − − 2.5 − − 2.5 LM293 Tlow = −25°C, Thigh = +85°C LM393 Tlow = 0°C, Thigh = +70°C LM2903 Tlow = −40°C, Thigh = +105°C LM2903V & NCV2903 Tlow = −40°C, Thigh = +125°C NCV2903 is qualified for automotive use. 4. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause excessive heating and eventual destruction. 5. At output switch point, VO]1.4 Vdc, RS = 0 W with VCC from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to VCC = −1.5 V). 6. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state, therefore, no loading changes will exist on the input lines. 7. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of common mode range is VCC −1.5 V. 8. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are obtainable. 9. The comparator will exhibit proper output state if one of the inputs becomes greater than VCC, the other input must remain within the common mode range. The low input state must not be less than −0.3 V of ground or minus supply. |
类似零件编号 - LM2903VDR2G |
|
类似说明 - LM2903VDR2G |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |