数据搜索系统,热门电子元器件搜索 |
|
AM29F800B-120SIB 数据表(PDF) 8 Page - Advanced Micro Devices |
|
AM29F800B-120SIB 数据表(HTML) 8 Page - Advanced Micro Devices |
8 / 41 page 8 Am29F800T/Am29F800B 8/18/97 PR E L IM IN A R Y Table 1. Am29F800 User Bus Operations (BYTE = VIH) Table 2. Am29F800 User Bus Operations (BYTE = VIL) Legend: L = logic 0, H = logic 1, X = Don’t Care. See Characteristics for voltage levels. Notes: 1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Table 7. 2. Refer to the section on Sector Protection. Read Mode The Am29F800 has two control functions which must be satisfied in order to obtain data at the outputs. CE is the power control and should be used for device selec- tion. OE is the output control and should be used to gate data to the output pins if a device is selected. Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the delay from stable addresses and stable CE to valid data at the output pins. The output enable access time is the delay from the fa lling edge of OE to va lid data at the output pins (assuming the addresses have been stable for at least tACC–tOE time). Standby Mode There are two ways to implement the standby mode on the Am29F800 device, both using the CE pin. A CMOS standby mode is achieved with the CE input held at VCC ± 0.3V. Under this condition the current is typically reduced to less than 5 µA. A TTL standby mode is achieved with the CE pin held at VIH. Under this condition the current is typically reduced to 1 mA. Operation CE OE WE A0 A1 A6 A9 DQ0–DQ15 RESET Autoselect, AMD Manuf. Code (Note 1) L L H L L L VID Code H Autoselect Device Code (Note 1) L L H H L L VID Code H Read L L X A0A1A6A9 DOUT H Standby H XXXX XX HIGH Z H Output Disable L H H X X X X HIGH Z H Write L H L A0 A1 A6 A9 DIN H Verify Sector Protect (Note 2) L L H L H L VID Code H Temporary Sector Unprotect X XXXX XX X VID Hardware Reset X XXXX XX HIGH Z L Operation CE OE WE A0 A1 A6 A9 DQ0–DQ7 DQ8–DQ15 RESET Autoselect, AMD Manuf. Code (Note 1) L L H LLL VID Code HIGH Z H Autoselect Device Code (Note 1) L L H H L L VID Code HIGH Z H Read L L X A0A1A6A9 DOUT HIGH Z H Standby H X XXXXX HIGH Z HIGH Z H Output Disable L H H XXXX HIGH Z HIGH Z H Write L H L A0 A1 A6 A9 DIN HIGH Z H Verify Sector Protect (Note 2) L L HLHL VID Code HIGH Z H Temporary Sector Unprotect XX XXXXX X HIGH Z VID Hardware Reset X X XXXXX HIGH Z HIGH Z L |
类似零件编号 - AM29F800B-120SIB |
|
类似说明 - AM29F800B-120SIB |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |