数据搜索系统,热门电子元器件搜索 |
|
AD8340-EVAL 数据表(PDF) 11 Page - Analog Devices |
|
AD8340-EVAL 数据表(HTML) 11 Page - Analog Devices |
11 / 20 page AD8340 Rev. 0 | Page 11 of 20 I-Q ATTENUATORS AND BASEBAND AMPLIFIERS The proprietary linear-responding attenuator structure is an active solution with differential inputs and outputs that offer excellent linearity, low noise, and greater immunity from mis- matches than other variable attenuator methods. The gain, in linear terms, of the I and Q channels is proportional to its control voltage with a scaling factor designed to be 2/V, i.e., a full-scale gain setpoint of 1.0 (−2 dB) for VBBI (Q) of 500 mV. The control voltages can be driven differentially or single-ended. The combi- nation of the baseband amplifiers and attenuators allows for maximum modulation bandwidths in excess of 200 MHz. OUTPUT AMPLIFIER The output amplifier accepts the sum of the attenuator outputs and delivers a differential output signal into the external load. The output pins must be pulled up to an external supply, preferably through RF chokes. When the 50 Ω load is taken differentially, an output P1dB and IP3 of 11 dBm and 24 dBm is achieved, respectively, at 880 MHz. The output can be taken in single-ended fashion, albeit at lower performance levels. NOISE AND DISTORTION The output noise floor and distortion levels vary with the gain magnitude but do not vary significantly with the phase. At the higher gain magnitude setpoints, the OIP3 and the noise floor vary in direct proportion with the gain. At lower gain magni- tude setpoints, the noise floor levels off while the OIP3 continues to vary with the gain. GAIN AND PHASE ACCURACY There are numerous ways to express the accuracy of the AD8340. Ideally, the gain and phase should precisely follow the setpoints. Figure 3 illustrates the gain error in dB from a best fit line, normalized to the gain measured at the gain setpoint = 1.0, for the different phase setpoints. Figure 6 shows the gain error in a different form; the phase setpoint is swept from 0° to 360° for different gain setpoints. Figure 8 and Figure 22 show analo- gous errors for the phase error as a function of gain and phase setpoints. The accuracy clearly depends on the region of opera- tion within the vector gain unit circle. Operation very close to the origin generally results in larger errors as the relative accuracy of the I and Q vectors degrades. RF FREQUENCY RANGE The frequency range on the RF input is limited by the internal polyphase quadrature phase-splitter. The phase-splitter splits the incoming RF input into two signals, 90° out of phase, as previously described in the RF Quadrature Generator section. This polyphase network has been designed to ensure robust quadrature accuracy over standard fabrication process parame- ter variations for the 700 MHz to 1 GHz specified RF frequency range. Using the AD8340 as a single-sideband modulator and measuring the resulting sideband suppression is a good gauge of how the quadrature accuracy is maintained over RF frequency. A typical plot of sideband suppression from 500 MHz to 1.5 GHz is shown in Figure 28. The level of side- band suppression degradation outside the 700 MHz to 1 GHz specified range will be subject to manufacturing process variations. 0 –5 –10 –15 –20 –25 –30 –35 500 1500 1400 1300 1200 1100 1000 900 800 600 700 FREQUENCY (MHz) Figure28.SidebandSuppressionvs.Frequency |
类似零件编号 - AD8340-EVAL |
|
类似说明 - AD8340-EVAL |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |