数据搜索系统,热门电子元器件搜索 |
|
L6997S 数据表(PDF) 9 Page - STMicroelectronics |
|
L6997S 数据表(HTML) 9 Page - STMicroelectronics |
9 / 30 page 9/30 L6997S at light load and in continuous mode at high load. The transition from PFM to PWM occurs when load current is around half the inductor current ripple. This threshold value depends on VIN, L, and VOUT. Note that the higher the inductor value is, the smaller the threshold is. On the other hand, the bigger the inductor value is, the slower the transient response is. The PFM waveforms may appear more noisy and asynchronous than normal opera- tion, but this is normal behaviour mainly due to the very low load. If the PFM is not compatible with the applica- tion it can be disabled connecting to VCC the NOSKIP pin. 4.4 Softstart After the device is turned on the SS pin voltage begins to increase and the system starts to switch. The softstart is realized by gradually increasing the current limit threshold to avoid output overvoltage. The active soft start range for the VSS voltage (where the output current limit increase linearly) is from 0.6V to 1V. In this range an internal current source (5 µA Typ) charges the capacitor on the SS pin; the reference current (for the current limit comparator) forced through ILIM pin is proportional to SS pin voltage and it saturates at 5 µA (Typ.). When SS voltage is close to 1V the maximum current limit is active. Output protections OVP & UVP are disabled until the SS pin voltage reaches 1V (see figure 8). Once the SS pin voltage reaches the 1V value, the voltage on SS pin doesn't impact the system operation any- more. If the SHDN pin is turned on before the supplies, the power section must be turned on before the logic section. While if the supplies are applied with the SHND pin off, the start up sequence doesn't meter. Figure 8. Soft -Start Diagram Because the system implements the soft start by controlling the inductor current, the soft start capacitor should be selected based on of the output capacitance, the current limit and the soft start active range ( ∆VSS). In order to select the softstart capacitor it must be imposed that the output voltage reaches the final value before the soft start voltage reaches the under voltage value (1V). After this UVP and OVP are enable. The time necessary to charge the SS capacitor up to 1V is given by: (7) In order to calculate the output voltage chargin time it should be considered that the inductor current function can be supposed linear function of the time. (8) Time Time 0.6V Maximum current limit Soft-start active range 5 µA 4.1V 1V Ilim current Vss T SS CSS () 1V Iss -------- C SS ⋅ = I L t,CSS () R ilim/Rdson K ILIM I SS t ⋅⋅ ⋅ () V SS C SS ⋅ ∆ () --------------------------------------------------------------------------- = |
类似零件编号 - L6997S |
|
类似说明 - L6997S |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |