数据搜索系统,热门电子元器件搜索 |
|
CS51414E 数据表(PDF) 10 Page - ON Semiconductor |
|
CS51414E 数据表(HTML) 10 Page - ON Semiconductor |
10 / 16 page CS51411, CS51412, CS51413, CS51414 http://onsemi.com 10 IRMS + IO D(1 * D) where: D = switching duty cycle which is equal to VO/VIN. IO = load current. Figure 10. Input Voltage Ripple in a Buck Converter To calculate the RMS current, multiply the load current with the constant given by Figure 11 at each duty cycle. It is a common practice to select the input capacitor with an RMS current rating more than half the maximum load current. If multiple capacitors are paralleled, the RMS current for each capacitor should be the total current divided by the number of capacitors. Figure 11. Input Capacitor RMS Current can be Calculated by Multiplying Y Value with Maximum Load Current at any Duty Cycle 0 0.2 0.4 1.0 Duty Cycle 0 0.1 0.3 0.4 0.5 0.6 0.2 0.6 0.8 Selecting the capacitor type is determined by each design’s constraint and emphasis. The aluminum electrolytic capacitors are widely available at lowest cost. Their ESR and ESL (equivalent series inductor) are relatively high. Multiple capacitors are usually paralleled to achieve lower ESR. In addition, electrolytic capacitors usually need to be paralleled with a ceramic capacitor for filtering high frequency noises. The OS–CON are solid aluminum electrolytic capacitors, and therefore has a much lower ESR. Recently, the price of the OS–CON capacitors has dropped significantly so that it is now feasible to use them for some low cost designs. Electrolytic capacitors are physically large, and not used in applications where the size, and especially height is the major concern. Ceramic capacitors are now available in values over 10 µF. Since the ceramic capacitor has low ESR and ESL, a single ceramic capacitor can be adequate for both low frequency and high frequency noises. The disadvantage of ceramic capacitors are their high cost. Solid tantalum capacitors can have low ESR and small size. However, the reliability of the tantalum capacitor is always a concern in the application where the capacitor may experience surge current. Output Capacitor In a buck converter, the requirements on the output capacitor are not as critical as those on the input capacitor. The current to the output capacitor comes from the inductor and thus is triangular. In most applications, this makes the RMS ripple current not an issue in selecting output capacitors. The output ripple voltage is the sum of a triangular wave caused by ripple current flowing through ESR, and a square wave due to ESL. Capacitive reactance is assumed to be small compared to ESR and ESL. The peak to peak ripple current of the inductor is: IP * P + VO(VIN * VO) (VIN)(L)(fS) VRIPPLE(ESR), the output ripple due to the ESR, is equal to the product of IP–P and ESR. The voltage developed across the ESL is proportional to the di/dt of the output capacitor. It is realized that the di/dt of the output capacitor is the same as the di/dt of the inductor current. Therefore, when the switch turns on, the di/dt is equal to (VIN – VO)/L, and it becomes VO/L when the switch turns off. The total ripple voltage induced by ESL can then be derived from VRIPPLE(ESL) + ESL( VIN L ) ) ESL( VIN * VO L ) + ESL( VIN L ) |
类似零件编号 - CS51414E |
|
类似说明 - CS51414E |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |