数据搜索系统,热门电子元器件搜索 |
|
K-TS1 数据表(PDF) 9 Page - RFbeam Microwave GmbH |
|
K-TS1 数据表(HTML) 9 Page - RFbeam Microwave GmbH |
9 / 13 page K-TS1 RADAR TESTSYSTEM Datasheet Select and Setting Tuning mode: (will become permanently stored in EEPROM) (Step 1:) [Enter] If necessay, terminate a previous cyclic display Step 2: [s] [Enter] Go to Setup Page Step 3: [m] [1] [Enter] Select Tuning Mode Step 4: [b] nn.nnn [Enter] Set lower limit of OK range Step 5: [n] nn.nnn [Enter] Set higher limit of OK range Step 6: [x] [Enter] SAVE SETTINGS and return to main page Step 8: Changes take place only after power on RFbeam K-TS1 24GHz Test System #09160210 ============================================== Sub-Page 'Setup' [m] Operating Mode : Tuning [0,1,2] (*) [b] Tuning Frequency low : 24.100 [23.300-24.900GHz] (*) [n] Tuning Frequency high : 24.150 [23.300-24.900GHz] (*) 0 = Normal, 1 = Tuning, 2 = Testbench [b] used in Tuning Mode only: 80% PWM [n] ] used in Tuning Mode only: 60% PWM [a] Identification : 09160210 [s] Oscillator Power : 7.0 [dBm] [d] Antenna Gain : 12.0 [dBi] [f] Antenna Center Frequency : 24.100 [GHz] [g] Antenna Loss low : 5.0 [dB] [h] Antenna Loss high : 10.0 [dB] [j] IF1 Gain : 0.2 [dB] [k] IF2 Gain : 1.0 [dB] [l] AUX Loss : 0.0 [dB] [y] Target Conversion Loss : 1.5 [dB] [-] Target Amplitude I : 48 [%] [-] Target Amplitude Q : 42 [%] [-] Target Offset I : 210 [mV] [-] Target Offset Q : 188 [mV] [-] Target Phase I/Q : 108 [Deg] FACTORY SETTINGS DO NOT ALTER! [x] Leave Setup and store User Parameters (*) ==> Choosing x key turns to main page Changing become active after power on Fig. 10: Settings for "Tuning Mode" Test Bench Mode A personalized Windows PC based Testbench Software may be purchased at www.rfbeam.ch. Get more informations at info@rfbeam.ch. Purpose: This mode corresponds fully to the Normal Mode, exept the digital I/O capabilities. In this mode, K-TS1 can be used in an Automated Test Equipment (ATE) for testing Radar Transceivers. It features a digital input, represented as 'CTS' modem signal. It may be used for starting a test procedure e.g. A digital output represents an 'RTS' modem signal and may be used for driving a "pass" LED or similar. Digital Input: Digital Input is available at TTL I/O Connection, Pin 1(pulled up) and Pin 3(GND). You may directly connect a switch or an open collector driver to these pins. This input is represented by the 'CTS' modem signal at the USB serial connection. Switch open: CTS active Digital Output: Digital Output is available at TTL I/O Connection, Pin 2(+) and Pin 3(GND). An LED may be driven via a series resistor by TTL I/O Connection. Selecting Testbench Mode: (will become permanently stored in EEPROM) (Step 1:) [Enter] If necessay, terminate a previous cyclic display Step 2: [s] [Enter] Go to Setup Page Step 3: [m] [2] [Enter] Select Testbench Mode Step 4: [x] [Enter] SAVE SETTINGS and return to main page Step 5: Changes take place only after power on © RFbeam Microwave GmbH www.rfbeam.ch 2011-03-11 Page 9/13 |
类似说明 - K-TS1 |
|
|
链接网址 |
隐私政策 |
ALLDATASHEETCN.COM |
ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |