ACT2803 datasheet(14/22 Pages) ACTIVE-SEMI

部件名	ACT2803

功能描述	5V/2.4A Dual Cell Battery Power Manager

Download	22 Pages

Scroll/Zoom	100%

制造商	ACTIVE-SEMI [Active-Semi, Inc]

网页	http://www.active-semi.com

标志

14 / 22 page

Rev 1, May-12-2016

Innovative PowerTM

- 14 -

www.active-semi.com

ACT2803

APPLICATIONS INFORMATION

HYST pin is regulated at 1V. Its input current will

determine hysteresis adjustment equally to all level.

Connect HYST to APGN via a resistor to set

hysteresis window.

Beside the hysteresis window, to avoid comparison

oscillation, fixed 100mV of hysteresis is added to

each LEVEL comparator.

Hysteresis window is given by below equation:

RHYST Example is given by the below table:

Battery Impedance Compensation

To avoid the number of LEDs changes between

charge and discharge modes. Internal impedance

compensation circuit is built in. An external resistor

is used to set the impedance from 100mΩ to

800mΩ.

RIMC

is

corresponding

to

battery

impedance. The LED1-4 thresholds shifted up and

down based on the product of charge/discharge

current and set impedance. RIMC value is given by

below equation.

In case not using compensation, float RIMC then

there is no compensation affects to trig-points.

RIMC example is given by the below table:

Battery Temperature Monitering

The

ACT2803

monitors

the

battery

pack

temperature by measuring TH voltage at the TH pin

as shows in Figure 4. The TH pin is connected to

the thermistor resistor net which includes a negative

temperature coefficient thermistor. An internal

current source provides a bias current to generate

TH voltage. The ACT2803 compares the voltage at

the TH pin with the internal VTHH and VTHL

thresholds to determine if charging or discharging is

allowed. When VTH<VTHL or VTH >VTHH, it will be

triggered latch off fault, there is 3 ways to wake up

ACT2803 when VTH returns to the normal range.

1. Push PB when latch off bit is not set

2. I2C to clear faults in standby

3. Plug Vin to power up

Figure 4:

Thermistor setting

RNTCc : NTC Resistor at cold temperature (Tcold)

RNTCh : NTC Resistor at hot temperature (Thot)

From (7) (8) (9) and (10) calculate Ra and Rb in

charge mode, as the same method, the resistors in

discharge mode can be calculated.

For example, use NXRT15XH103 NTC resistor, the

temperature in charge mode is 0℃ to 45℃,we

know RNTCC=27.219k and 4.917k at 0℃ to 45℃,

respectively. We can calculate Ra=33kΩ and

Rb=2.87kΩ based on the above formulas. As the

same method we can calculate the value when the

temperature is -20℃ to 60℃.

Cell Balance Setting

ACT2803 has integrated a cell balance feature to

reduce the un-balance charge between dual

batteries. Normally cell balance is activated during

Fast Charge and Top Off modes.



4

)

(





K

HYST

R

54K

V

HYST

RHYST (kΩ)

LED1

VHYST

LED2

VHYST

LED3

VHYST

LED4

VHYST

Floating

0mV

270

120mV

100mV

135

240mV

200mV

90

360mV

300mV

67.5

480mV

400mV

54

600mV

500mV

45

720mV

600mV

)

6

(

)

(

)

(

2160

)

(











m

R

m

R

k

R

BAT

CS

IMC

RBAT (mΩ)

100

200

300

400

500

600

700

RCS = 25 mΩ

540k 270k 180k 135k 108k 90k

77k

RCS = 50 mΩ

1080k 540k 360k 270k 216k 180k 154k

)

7

(

hot

Rc

I

V

CHG

TCL





)

9

(

NTCh

R

Ra

R

Ra

Rb

hot

Rc









)

10

(

NTCc

R

Ra

R

Ra

Rb

cold

R









)

8

(

cold

R

I

V

CHG

TCH





+

–

+

–

TH

VTCL=1V

NTC

VTCH=2.5V

+

–

+

–

VTDL=0.57V

VTDH=2.5V

IDIS=100uA

ICHG=140uA

ACT2803

CHG_HOT

CHG_COLD

DIS_HOT

DIS_COLD

Rb

Ra

Li+ Battery

Pack

 5

*

6

.

0

1

:

2

*

5

.

0

3

:

4

HYST

V

HYST

V

HYST



类似零件编号 - ACT2803

制造商	部件名	数据表	功能描述
Active-Semi, Inc	ACT2803QJ-T	523Kb / 22P	5V/2.4A Dual Cell Battery Power Manager Rev 1, May-12-2016
	ACT2803QJ-T0435	523Kb / 22P	5V/2.4A Dual Cell Battery Power Manager Rev 1, May-12-2016
	ACT2803	523Kb / 22P	5V/2.4A Dual Cell Battery Power Manager Rev 1, May-12-2016

More results

类似说明 - ACT2803

制造商	部件名	数据表	功能描述
Active-Semi, Inc	ACT2803	523Kb / 22P	5V/2.4A Dual Cell Battery Power Manager Rev 1, May-12-2016
	ACT2804	558Kb / 23P	5V/3.4A Dual Cell Battery Power Manager Rev 3, Apr-17-2017
	ACT2804	1Mb / 20P	5V/3.4A Dual Cell Backup Battery Power Manager Rev 2, Feb-04-2016
	ACT2804	1Mb / 20P	5V/3.4A Dual Cell Backup Battery Power Manager Rev 2, Feb-04-2016
	ACT2823	1Mb / 25P	Dual Cell Li-Ion Battery Charger and Power Bank Manager REV 1, 01-DEC-2016
	ACT2823	1Mb / 25P	Dual Cell Li-Ion Battery Charger and Power Bank Manager REV 1, 01-DEC-2016
Intersil Corporation	ISL94212	151Kb / 2P	Multi-Cell Li-Ion Battery Manager
Intersil Corporation	ISL78610	1Mb / 98P	Multi-Cell Li-Ion Battery Manager
Dallas Semiconductor	DS2441	134Kb / 29P	1-Cell Li-Ion Battery Manager
Renesas Technology Corp	ISL78600	3Mb / 105P	Multi-Cell Li-Ion Battery Manager